You boot a Cisco TelePresence System TX1300. Six check marks appear in the lower left-hand corner. The IP
address 192.168.100.2 is displayed in the lower right-hand corner. A DHCP server is configured on the
network.
Which of the following statements is most likely to be correct?
A.
The CTS TX1300 and DHCP server are operating normally.
B.
The CTS TX1300 cannot reach the DHCP server.
C.
The CTS TX1300 does not have network connectivity.
D.
The CTS TX1300 has experienced a compact flash error.
Explanation:
The Cisco TelePresence System (CTS) TX1300 cannot reach the Dynamic Host Configuration Protocol
(DHCP) server. If the CTS TX1300 cannot reach a DHCP server, it will configure itself with the IP address
192.168.100.2. Therefore, you should check the DHCP server as well as the devices between the CTS TX1300
and the DHCP server.
The CTS TX1300 has network connectivity because the fourth circle in the lower left-hand corner displays a
check mark. If the fourth circle contains a red X, you should check the network port and the connected Ethernet
cable.
The CTS TX1300 has not experienced a compact flash error, because the sixth circle in the lower left-hand
corner displays a check mark. If the sixth circle contains a red X, the CTS TX1300 has experienced a compact
flash error. You should contact Cisco Technical Support if you receive this error.Cisco: First-Time Setup: Loading your Software and Initial System Configuration
(9/Jan/2018 Updated) New 210-065 Exam Questions:
NEW QUESTION 347
Which effect of the CLI set audio aec enable command on the immersive Cisco Telepresence system is true?
A. Echo cancellation is enabled.
B. Call economy quality feature is enabled.
C. Noise cancellation is enabled.
D. AEC audio codec is enabled.
Answer: A
NEW QUESTION 348
What is the process for resetting a Cisco VCS control appliance back to initial default configuration?
A. Push down and hold the reset button on the back of the VCS appliance for 10 seconds and power cycle the device.
B. Log onto the CLI console as root and initiate the defaults-reset command.
C. Log into the GUI interface as administrator, choose System Settings, select Restore, select Factory Reset.
D. Log onto the CLI console as root and initiate the factory-reset command.
Answer: D
NEW QUESTION 349
Which two Cisco TelePresence endpoints support hosting embedded multisite conferences? (Choose two.)
A. SX20
B. MX800
C. DX70
D. DX80
E. Jabber Video for Cisco TelePresence
Answer: AB
NEW QUESTION 350
Which option is the Cisco recommended layout if cascading is being used?
A. Enhanced Continuous Presence
B. Full Participant
C. Continuous Presence
D. Active Speaker
Answer: C
NEW QUESTION 351
A Cisco EX60 is connected to the network, but users cannot make calls and the device is unregistered. The voice engineer configured the device on Cisco Unified Communications Manager. Which two options are causes of this problem? (Choose two.)
A. SIP URI is not configured correctly.
B. H.323 parameters are not configured correctly.
C. IP address is in a different subnet.
D. No user is associated to a device.
E. SIP proxy is not configured correctly.
Answer: DE
NEW QUESTION 352
Which desktop endpoint support 802.3af PoE?
A. DX70
B. DX80
C. DX90
D. DX650
Answer: D
0
0
NEW QUESTION 353
An engineer is backing up a VCS configuration. Which two methods can be used? (Choose two.)
A. FTP
B. SFTP
C. SSH
D. Web administration
E. Local
Answer: BC
NEW QUESTION 354
An engineer sees a video camera icon on the Cisco IP phone screen status line. Which meaning of this icon is true?
A. The Cisco VT camera is connected to the PC, and the PC is connected to the Cisco IP phone.
B. The Cisco IP phone has web access.
C. The Cisco IP phone is receiving a video call.
D. The Cisco IP phone is configured with video capabilities.
Answer: D
NEW QUESTION 355
When an administrator schedules a conference, which three devices are part of the process? (Choose three.)
A. Endpoint
B. Cisco Prime Collaboration Manager
C. Cisco TelePresence Management Suite
D. Cisco Communications Manager
E. MCU appliance
F. Cisco TelePresence Content Server
Answer: BDF
NEW QUESTION 356
Which option is an immersive endpoint?
A. Cisco TelePresence EX90
B. Cisco TelePresence TX9000
C. Cisco TelePresence SX10
D. Cisco TelePresence DX70
Answer: C
NEW QUESTION 357
An engineer is using a cascading feature with Cisco TelePresence Conductor and Cisco TelePresence Servers. Which two limitations will the engineer likely encounter? (Choose two.)
A. Ad-hoc conferencing cascading is not supported.
B. Only single-screen endpoints are supported through cascading links.
C. Multiple-screen endpoints are supported only with three or more Cisco TelePresence Servers.
D. Scheduled conferencing is not supported.
E. Ad-hoc conferencing cascading is supported only with three or more Cisco TelePresence Servers.
Answer: AD
0
0
What’s more, part of the new 363Q 210-065 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpfjREa25iSExKUkxvQi12aVdDMWNJSGs0T2JwYkhVUmtwdXhETmZVR3ZNek0
Best Regards!
0
0