Which of the following commands should you issue from policy-map class configuration mode? (Select the best an
You are creating a policy map for VoIP packets. VoIP packets must receive 30 percent of the bandwidth on the S0/0 interface. Jitter and delay should be minimized. Which of the following commands should you issue from policy-map class configuration mode? (Select the best answer.) A. priority 30 B. priority percent 30 C. bandwidth 30 […]
Which of the following statements are true regarding Cisco PfR? (Select 2 choices.)
Which of the following statements are true regarding Cisco PfR? (Select 2 choices.) A. Active mode generates probes for all exit paths. B. Passive mode generates probes for all exit paths. C. Active mode monitors delay, packet loss, throughput, and reachability. D. Both active mode and passive mode monitor reachability and delay. E. Active mode […]
Switch1 and Switch2 are configured as a VSS. Switch1 has a higher priority. Switch2 has a higher switch ID. Bo
Switch1 and Switch2 are configured as a VSS. Switch1 has a higher priority. Switch2 has a higher switch ID. Both switches are started simultaneously. Which of the following will occur if RRP discovers an incompatibility between the switches? (Select the best answer.) A. Both switches will come up in RPR mode. B. Both switches will […]
Which of the following paths are allowed by the AS path filter? (Select the best answer.)
You issue the ip as-path access-list 1 permit ^7_23$ command on a BGP router. Which of the following paths are allowed by the AS path filter? (Select the best answer.) A. paths that originate from AS 7 or AS 23 B. paths that pass through AS 7 or AS 23 C. paths that originate from […]
Which of the following commands can you issue to enable RSTP? (Select 2 choices.)
Which of the following commands can you issue to enable RSTP? (Select 2 choices.) A. spanning-tree mode mst B. spanning-tree mode pvst C. spanning-tree mode rapid-pvst D. no spanning-tree mode Explanation: You can issue the spanning-tree mode mst command or the spanning-tree mode rapid-pvst command to enable Rapid Spanning Tree Protocol(RSTP). RSTP, which is defined […]
Which of the following statements regarding BFD are correct? (Select 2 choices.)
Which of the following statements regarding BFD are correct? (Select 2 choices.) A. BFD is supported by OSPF, EIGRP, BGP, and IS-IS. B. BFD detects link failures in less than one second. C. BFD can bypass a failed peer without relying on a routing protocol. D. BFD creates one session per routing protocol per interface. […]
You administer several switches on a network. The switches are configured with the default MLD snooping settin
You administer several switches on a network. The switches are configured with the default MLD snooping settings. Several VLANs are configured on each switch. Which of the following statements is most accurate? (Select the best answer.) A. The switches will not forward IPv6 multicast traffic. B. The switches will forward IPv6 multicast traffic to every […]
Which of the following is accomplished by implementing MPP on a router? (Select the best answer.)
Which of the following is accomplished by implementing MPP on a router? (Select the best answer.) A. Only hosts on a particular subnet will be able to remotely manage the router. B. Only hosts that are connected to a particular interface will be able to remotely manage the router. C. Only hosts that perform 802.1X […]
Which of the following partial output from the show ip cache flow command would you expect to see for an HTTP
Which of the following partial output from the show ip cache flow command would you expect to see for an HTTP connection sent from 10.1.1.36? (Select the best answer.) A. SrcIF SrcIPaddress DstIf DstIPaddress Pr SrcP DstP PktsEt0/0 10.1.1.36 Et1/0 10.2.1.74 06 C486 0050 1 B. SrcIF SrcIPaddress DstIf DstIPaddress Pr SrcP DstP PktsEt0/0 10.1.1.36 […]
Which of the following statements must be true? (Select the best answer.)
RouterA and RouterB are connected routers. You issue the show clns neighbors command on RouterA and receive the following output: System Id Interface SNPA State Holdtime ….. Type Protocol RouterB Et0/0 0000.0000.000b Up 23 L1 IS-IS Which of the following statements must be true? (Select the best answer.) A. RouterA and RouterB are in the […]