The four switches in the diagram below have default configurations. Considering the bandwidths indicated on each link and the MAC addresses indicated for each
switch, which ports will be forwarding after RSTP has converged? (Choose all that apply.)

A.
SW 1 port that connects to SW 4

B.
SW 1 port that connects to SW 2

C.
SW 1 port that connects to SW 3

D.
SW 2 port that connects to SW 3

E.
SW 2 port that connects to SW 4

F.
SW 3 port that connects to SW 4

G.
SW 3 port that connects to SW 1

H.
SW 3 port that connects to SW 2

Explanation:
The ports that will be forwarding after convergence are the SW1 port that connects to SW4, the SW2 port that connects to SW3, and all of the ports on SW3. The
process of determining these port states occurs in this order:
1. Selection of the root bridge. All ports on the root bridge become designated ports and are set to forward.
2. Determination of the root ports on each non-root bridge.
3. Determination of the designated port on each segment that does not connect directly to the root bridge.
4. Designated and root ports will be set to forwarding, and all other ports will be set to discarding.
For step 1, when all bridge priorities have been left to their default, all switches will have same bridge priority. When that is the case, as in this scenario, the switch
with the lowest MAC address will be selected as root bridge. In this case, SW3 has the lowest MAC address and becomes the root bridge. ALL ports are in a
forwarding state on the root bridge, which explains why all of the ports on SW3 will be in a forwarding state.
For step 2, each non-root bridge will select the interface it possesses with the least cost path to the root bridge. Once selected, that port will be placed in a
forwarding state. 100 Mbps links will be assigned a cost of 19, and 1 Gbps links will be assigned a cost of 4. Each path cost is the cumulative cost of the links in the
path. The root ports for the non-root bridges are determined as follows.
SW1 has four paths to the root bridge, with each path yielding the following costs:
SW1 to SW3 (100 Mbps) cost = 19
SW1 to SW4 to SW3 (1 Gbps + 1 Gbps) cost = 4 + 4 = 8
SW1 to SW2 to SW 4 to SW3 (100 Mbps + 100 Mbps + 1 Gbps) cost = 19 + 19 + 4 = 42
SW1 to SW2 to SW3 (100 Mbps + 1 Gbps) cost = 19 + 4 = 23
SW1 will use the lowest cost path (SW1 to SW4 to SW3) as its root path. It will set the SW1 connection to SW4 to forwarding and the connection from SW1 to SW3
to blocking. The status of its third interface (SW1 to SW2) will be determined in Step 3, since it is a shared segment with SW2 that does not have a direct
connection to the root bridge.
Switch 2 (SW2) has three paths to the root bridge, with each path yielding the following costs:
SW2 to SW3 (1 Gbps) cost = 4
SW2 to SW1 to SW3 (100 Mbps + 100 Mbps) cost = 19 + 19 = 38
SW2 to SW4 to SW3 (100 Mbps + 1 Gbps) cost = 19 + 4 = 23
SW2 will use the lowest cost path (SW2 to SW3) as its root path and will set the SW2 connection to SW3 to forwarding. The status of its second and third interfaces
(SW2 to SW1 and SW2 to SW4) will be determined in step 3 since both are shared segments with SW2 and SW4 respectively that do not have a direct connection
to the root bridge.
Switch 4 (SW4) has four paths to the root bridge, with each path yielding the following costs:
SW4 to SW3 (1 Gbps) cost = 4
SW4 to SW1 to SW3 (1 Gbps + 100 Mbps) cost = 4+19 = 23
SW4 to SW2 to SW1 to SW3 (100 Mbps + 100 Mbps + 100 Mbps) cost = 19 + 19 + 19 = 57
SW4 to SW2 to SW3 (1 Gbps + 100 Mbps) cost = 4 +19 = 23
SW4 will use the lowest cost path (SW4 to SW3) as its root path and set the SW4 connection to SW3 to forwarding. The status of SW4’s second and third
interfaces, SW4 to SW1 and SW4 to SW2, will be determined in step 3. Since these interfaces are shared segments with SW1 and SW2, they do not have a direct
connection to the root bridge.

For Step 3, there are two segments in the diagram (SW1 to SW2 and SW2 to SW4) that do not connect directly to the root bridge. The interface on either end of the
segment that has the least cost path to the root bridge will be the designated port for that section.
The designated port of each segment is determined in this way.
For the SW1 to SW2 segment, the SW2 end of the segment has a shortest path cost of 1 Gbps (4) to the root, and the SW1 end of the segment has a shortest
path cost through SW4 of 2 Gbps (8) to the root. The SW2 port to SW1 will be the designated port and will be forwarding.
For the SW2 to SW4 segment, the SW2 end of the segment has a shortest path cost of 1 Gbps (4) to the root and the SW4 end of the segment has a shortest
path cost of 1 Gbps (4) to the root. This is a tie. In the case of a tie, the interface connected to the switch with the lowest MAC address becomes the designated
port for the segment. SW4 has the lowest MAC address, so the SW4 port to SW2 will be the designated port and will be forwarding.
Once determined, the designated and root ports will be set to forwarding and all other ports will be set to discarding. The converged state of all ports is shown in the
diagram below.

Once STP has converged, the port states will determine the path used when sending traffic from a host connected to one switch to a host connected to another
switch. For example, if a host connected to SW3 were destined for a host connected to SW2, the path taken would be SW3 to SW2. It would not take SW3-SW1-
SW2 or SW3-SW4-SW2 because on both of those paths, STP is blocking at least one port in the path.
Objective:

LAN Switching Fundamentals
Sub-Objective:
Configure, verify, and troubleshoot STP protocols

Home > Support > Technology Support > LAN Switching > Spanning Tree Protocol > Technology Information>Technology White Paper>Understanding Rapid
Spanning Tree Protocol (802.1w)