Refer to the exhibit.
An administrator cannot connect from R1 to R2. To troubleshoot this problem, the administrator has entered the command shown in the exhibit. Based on the
output shown, what could be the problem?
A.
The serial interface is configured for the wrong frame size.
B.
The serial interface does not have a cable attached.
C.
The serial interface has the wrong type of cable attached.
D.
The serial interface has a full buffer.
E.
The serial interface is configured for half duplex.
Can anyone please provide explanation about this question?
0
0
I may be wrong, but I think part of the output is missing. I think DTE & DCE both use v.35 cable (might be wrong on that).
The sh controllers command should show the type of cable connection being used (DCE/DTE)…or at least that is the way it appears in the Packet Tracer simulator.
0
0
As per the given output for DTE interface on R1 , the cable type ( V.35 ) is not the appropriate cable to connect between DTE and DCE .
0
0
wow so helpful
1
0
I have already passed Cisco 100-105 certification exam today! Scored 989/1000 in Australia. SO MANY new added exam questions which made me headache….. Anyway, I finally passed 100-105 exam with the help of the dump below!
QUESTION 81
Refer to the exhibit. If host A sends an IP packet to host B, what will the source physical address be in the frame when it reaches host B?
A. 10.168.10.99
B. 10.168.11.88
C. A1:A1:A1:A1:A1:A1
D. B2:B2:B2:B2:B2:B2
E. C3:C3:C3:C3:C3:C3
F. D4:D4:D4:D4:D4:D4
Answer: E
Explanation:
When packets transfer from one host to another across a routed segment, the source IP address always remains the same source IP address, and the source physical (MAC) address will be the existing router’s interface address. Similarly, the destination IP address always remains the same and the destination physical (MAC) address is the destination router’s interface address.
QUESTION 82
Refer to the exhibit. HostX is transferring a file to the FTP server. Point A represents the frame as it goes toward the Toronto router. What will the Layer 2 destination address be at this point?
A. abcd.1123.0045
B. 192.168.7.17
C. aabb.5555.2222
D. 192.168.1.1
E. abcd.2246.0035
Answer: E
Explanation:
For packets destined to a host on another IP network, the destination MAC address will be the LAN interface of the router. Since the FTP server lies on a different network, the host will know to send the frame to its default gateway, which is Toronto.
QUESTION 83
Which network device functions only at Layer 1 of the OSI model?
A.
B.
C.
D.
E.
Answer: B
Explanation:
Most hubs are amplifying the electrical signal; therefore, they are really repeaters with several ports. Hubs and repeaters are Layer 1 (physical layer) devices.
QUESTION 84
Refer to the exhibit. The host in Kiev sends a request for an HTML document to the server in Minsk. What will be the source IP address of the packet as it leaves the Kiev router?
A. 10.1.0.1
B. 10.1.0.5
C. 10.1.0.6
D. 10.1.0.14
E. 10.1.1.16
F. 10.1.2.8
Answer: E
Explanation:
Although the source and destination MAC address will change as a packet traverses a network, the source and destination IP address will not unless network address translation
(NAT) is being done, which is not the case here.
QUESTION 85
Refer to the exhibit. As packets travel from Mary to Robert, which three devices will use the destination MAC address of the packet to determine a forwarding path? (Choose three.)
A. Hub1
B. Switch1
C. Router1
D. Switch2
E. Router2
F. Switch3
Answer: BDF
Explanation:
Switches use the destination MAC address information for forwarding traffic, while routers use the destination IP address information. Local Area Networks employ Layer 2 Switches and Bridges to forward and filter network traffic. Switches and Bridges operate at the Data Link Layer of the Open System Interconnect Model (OSI). Since Switches and Bridges operate at the Layer 2 they operate more intelligently than hubs, which work at Layer 1 (Physical Layer) of the OSI. Because the switches and bridges are able to listen to the traffic on the wire to examine the source and destination MAC address. Being able to listen to the traffic also allows the switches and bridges to compile a MAC address table to better filter and forward network traffic. To accomplish the above functions switches and bridges carry out the following tasks:
MAC address learning by a switch or a bridge is accomplished by the same method. The switch or bridge listens to each device connected to each of its ports and scan the incoming frame for the source MAC address. This creates a MAC address to port map that is cataloged in the switches/bridge MAC database. Another name for the MAC address table is content addressable memory orCAM table. When a switch or bridge is listening o the network traffic, it receives each frame and compares it to the MAC address table. By checking the MAC table the switch/ bridge are able o determine which port the frame came in on. If the frame is on the MAC table the frame is filtered or transmitted on only that port. If the switch determines that the frame is not on the MAC table, the frame is forwarded out to all ports except the incoming port.
QUESTION 86
Refer to the exhibit. Mary is sending an instant message to Robert. The message will be broken into a series of packets that will traverse all network devices. What addresses will populate these packets as they are forwarded from Router1 to Router2?
A.
B.
C.
D.
E.
Answer: B
Explanation:
The Source and Destination IP address is not going to change. Host 1 IP address will stay as being the source IP and the Host 2 IP address will stay the destination IP address. Those two are not going to change. For the MAC address it is going to change each time it goes from one hope to another. (Except switches… they don’t change anything) Frame leaving HOST 1 is going to have a source MAC of Host 1 and a destination MAC of Router1.
Router 1 is going to strip that info off and then will make the source MAC address of Router1’s exiting interface, and making Router2’s interface as the destination MAC address.
Then the same will happen… Router2 is going to change the source/destination info to the source MAC being the Router2 interface that it is going out, and the destination will be Host2’s MAC address.
QUESTION 87
Refer to the exhibit. A network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation?
A. a router with two Ethernet interfaces
B. a switch with two Ethernet interfaces
C. a router with one Ethernet and one serial interface
D. a switch with one Ethernet and one serial interface
E. a router with one Ethernet and one modem interface
Answer: C
Explanation:
Only a router can terminate a leased line attachment access circuit, and only a router can connect two different IP networks. Here, we will need a router with two interfaces, one serial connection for the line attachment and one Ethernet interface to connect to the switch on the LAN.
QUESTION 88
Which transport layer protocol provides best-effort delivery service with no acknowledgment receipt required?
A. HTTP
B. IP
C. TCP
D. Telnet
E. UDP
Answer: E
Explanation:
UDP provides a connectionless datagram service that offers best-effort delivery, which means that UDP does not guarantee delivery or verify sequencing for any datagrams. A source host that needs reliable communication must use either TCP or a program that provides its own sequencing and acknowledgment services.
QUESTION 89
……
I have uploaded all the real questions of 100-105 exam to my Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDdDNkZEswTDRMaVE
Welcome to download them freely!
0
0