List the BGP route selection steps in the correct order?
which configuration command should be used if the internal routers
When the border routers in a transit autonomous system are to be configured, which configuration command should be used if the internal routers within the transit autonomous system have no IGP route to reach the router interface of the EBGP neighbor?
As a technician at Domain .com you are required to match the correct show command to its usage
Which BGP path attribute is used to inform the BGP peer that the routing information
Which BGP path attribute is used to inform the BGP peer that the routing information that was presented in the original routing updates may have been lost when the updates were summarized?
Which two other BGP router commands are required on Domain 1 and Domain 2
SIMULATION
SIMULATION
Exhibit:
You work as a network engineer at Domain .com. In the Transit AS 65001, router P1R3 has no BGP routes in its routing table and as a result has a problem reaching any networks external to AS 65001.
Unlike router P1R3, the other routers in AS 65002 (P1R1, P1R2 and P1R4) are not experiencing any network connectivity issue.
All BGP routes are properly inserted into the P1R4 routing table as shown below.
P1R4#sh route bpg
B 192.168.12.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.13.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.14.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.24.0/24 [200/0] via 10.200.200.12, 00:00:22
B 192.168.11.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.21.0/24 [200/0] via 10.200.200.12, 00:00:21
10.0.0.0/8 is variable subnetted, 9 subnets, 3 masks
B 10.0.0.0/8 [200/0] via 10.200.200.12, 00:00:26
B 192.168.23.0/24 [200/0] via 10.200.200.12, 00:00:22
B 192.168.22.0/24 [200/0] via 10.200.200.12, 00:00:21
Task:
1. Correct the configuration on Router P1R3 so its routing table shows the various BGP routes.
2. On router P1R3, adjust the default weight on all of the IBGP updates from router P1R2 in order to cause P1R3’s BGP path selection process to choose the path through router P1R2 to0 exit AS 65001. Do this without initiating a hard BGP neighbor reset.
which configuration command should be used
When the border routers in a transit autonomous system are to be configured, which configuration command should be used if the internal routers within the transit autonomous system have no IGP route to reach the router interface of the EBGP neighbor?
Place the BGP attributes in the correct order as they are examined by the BGP route selection process?
which one of the following from the State/PfxRcd field
When you are verifying a BGP neighbor relationship using the show ip bgp summary command, which one of the following from the State/PfxRcd field of the show output will confirm that the neighbor relationship has been established?
DRAG DROP
DRAG DROP
Based on the physical topology of AS 50001, to reduce the IBGP full-mesh requirements, only two redundant route reflectors (RR) will be used in a single cluster. In this case, which two routers should be the RRs and which three routers should be the clients based on the recommended route reflector design rule? Task: 1) Drag the matching text labels given on the left side of the topology to the correct targets on the right to identify these routers.
2) Also, identify all the unnecessary IBGP sessions once the redundant RRs have been configured by clicking on the IBGP session links to disable them. You can re-enable the IBGP sessions link by clicking on it again.