Refer to the exhibit.

You are required to implement traffic segmentation in the network. See the table for
relevant device details:
L2SW4, L2SW5, and L2SW6 are connected to L3SW1 with 802.1Q trunks with VLAN 191
and VLAN 398 allowed on the trunk.
You have the following information from L3SW1:
L3SW1# show run interfaces
interface Vlan1
no ip address
shutdown
interface Vlan2
ip address 10.2.2.2 255.255.255.248
interface Vlan191
ip address 10.10.27.126 255.255.255.192
interface Vlan200
ip address 10.20.20.1 255.255.255.248
interface Vlan398
ip address 10.15.153.1 255.255.255.0
L3SW1# show ip route
*** Output Omitted ***
10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks
C 10.2.2.1/29 is directly connected, Vlan2
C 10.10.27.64/26 is directly connected, Vlan191
C 10.15.153.0/24 is directly connected, Vlan398
C 10.20.20.0/29 is directly connected, Vlan200
S 10.200.200.0/24 [1/0] via 10.20.20.2
S* 0.0.0.0/0 [1/0] via 10.2.2.1
You are required to implement a configuration that will meet the following connectivity requirements:
The Administrator’s Station must have full access to PanelView PanelView should have limited access, based on specific TCP ports, to PLC#1 and I/O#1
The Administrator’s Station should have no access to PLC#1 and I/O#1
PLC#1 and I/O#1 should be able to communicate with each other on any port.

Which action will allow you to meet the connectivity requirements?

Refer to the exhibit.

Which lines represent a CIP connection being established between two devices?

A shutdown in the cookie cutter machine was traced to a broken network cable.
What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)

Refer to the exhibit.

L3SW1 has a spanning-tree priority of 8192 set on VLANs 1, 300, and 301, and these
VLANs are configured on and trunked between all switches.
Executing the command show spanning-tree blockedports on L2SW5 results in:

L2SW5# show spanning-tree blockedports
Name Blocked Interfaces List
——————– ————————————
VLAN0001 Gi1/1
VLAN0300 Gi1/1
VLAN0301 Gi1/1
An additional VLAN, VLAN302, is defined on all switches and trunked between them.
VLAN302 access ports are set up on each of the switches and PLC#1, I/O#1, and the
PanelView are attached. You expect the new VLAN to be listed as blocked on interface
GigabitEthernet1/1 of L2SW5 but it is not. The three new devices are able to communicate
with each other.

After executing the same command on all switches you see this output on L2SW4:
L2SW4# show spanning-tree blockedports
Name Blocked Interfaces List
——————– ————————————
VLAN0001 Gi1/2
VLAN0300 Gi1/2
VLAN0301 Gi1/2

Why is VLAN302 forwarding on L2SW5 interface GigabitEthernet 1/1 and L2SW4 interface GigabitEthernet 1/1 and 1/2?

Which is an issue with running CIP Motion on a REP network and identifies an alternate
resiliency protocol that works for CIP Motion?

To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted
by the switch, which command must be entered on the interface attached to the device?

To correctly integrate a Cisco Industrial Ethernet switch into a ProfiNET management
system such as SIMATIC STEP 7 or TIA Portal, which is a mandatory action?

Refer to the exhibit.

Which two parameters can be used to diagnose an overloaded system? (Choose two)

Which five are characteristics that describe Cisco Industrial switches? (Choose five)

A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC management station. The device is connected to interface FastEthernet1/3.
Based on the provided CLI output, which statement is correct?

switch#show profinet lldp
Fa1/1 port-003-00000 On
Fa1/2 port-004-00000 On
Fa1/3 port-005-00000 Off
Fa1/4 port-006-00000 Off
Fa1/5 port-007-00000 On
Fa1/6 port-008-00000 Off
Fa1/7 port-009-00000 On
Fa1/8 port-010-00000 Off