Which BGP path attribute is used to inform the BGP peer that the routing information
Which BGP path attribute is used to inform the BGP peer that the routing information that was presented in the original routing updates may have been lost when the updates were summarized?
Click and drag the elements on the left to the correct identifier on the right?
DRAG DROP
Refer to Exhibit. MPLS-TE is configured in the core and BFD is used for faster link failure detection. Currently the MPLS-TE tunnels are flapping. Identify the Symptom of the flapping, the root cause of the issue, and the resolution. Click and drag the elements on the left to the correct identifier on the right? It is possible that you will not use all the elements.
What is the maximum capacity of Cisco WCS Navigator
What is the maximum capacity of Cisco WCS Navigator when implemented with a Cisco Unified Wireless Network that is running version 7.0?
Which two other BGP router commands are required on Domain 1 and Domain 2
Exhibit
You work as a network administrator at Domain .com. Study the exhibit carefully. Which two other BGP router commands are required on Domain 1 and Domain 2 or on both so that Domain 2 can upload the input prefix-list named testing to Domain 1 to be used as an output filter? Select two.
Drag the attributes on the left to the appropriate categories on the right? Note that not all slots may be use
DRAG DROP
Drag the attributes on the left to the appropriate categories on the right? Note that not all slots may be uses.
SIMULATION
SIMULATION
Exhibit:
You work as a network engineer at Domain .com. In the Transit AS 65001, router P1R3 has no BGP routes in its routing table and as a result has a problem reaching any networks external to AS 65001.
Unlike router P1R3, the other routers in AS 65002 (P1R1, P1R2 and P1R4) are not experiencing any network connectivity issue.
All BGP routes are properly inserted into the P1R4 routing table as shown below.
P1R4#sh route bpg
B 192.168.12.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.13.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.14.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.24.0/24 [200/0] via 10.200.200.12, 00:00:22
B 192.168.11.0/24 [200/0] via 10.200.200.12, 00:00:26
B 192.168.21.0/24 [200/0] via 10.200.200.12, 00:00:21
10.0.0.0/8 is variable subnetted, 9 subnets, 3 masks
B 10.0.0.0/8 [200/0] via 10.200.200.12, 00:00:26
B 192.168.23.0/24 [200/0] via 10.200.200.12, 00:00:22
B 192.168.22.0/24 [200/0] via 10.200.200.12, 00:00:21
Task:
1. Correct the configuration on Router P1R3 so its routing table shows the various BGP routes.
2. On router P1R3, adjust the default weight on all of the IBGP updates from router P1R2 in order to cause P1R3’s BGP path selection process to choose the path through router P1R2 to0 exit AS 65001. Do this without initiating a hard BGP neighbor reset.
which configuration command should be used
When the border routers in a transit autonomous system are to be configured, which configuration command should be used if the internal routers within the transit autonomous system have no IGP route to reach the router interface of the EBGP neighbor?
How is password recovery performed on a Cisco 3300 Series MSE v7.0?
How is password recovery performed on a Cisco 3300 Series MSE v7.0?
Which statement is correct for the LWAPP/CAPWAP AP upstream encapsulated frame
Which statement is correct for the LWAPP/CAPWAP AP upstream encapsulated frame for a WMM- associated client frame that is centrally switched running v5.2?
Which command will prevent spanning-tree routing loops?
An FWSM is running in transparent mode. Which command will prevent spanning-tree routing loops?