The output displayed below is a result of what command?
The output displayed below is a result of what command? Interface Grp Fwd Pri State Address Active router Standby router Vl10 10 – 254 Active 192.168.8.10 local unknown Vl10 10 1 7 Active 0007.b400.0101 local – A. switch# show standby B. switch# show glbp C. switch# show standby brief D. switch# show glbp brief Explanation: […]
Which command enables HSRP on an interface?
Which command enables HSRP on an interface? A. hsrp B. standby ip C. standby mode hsrp D. switchport mode hsrp Explanation: The standby ip interface configuration command enables Hot Standby Router Protocol (HSRP). The syntax for this command is as follows: switch(config-if)# standby group-number ip ip-address The group-number argument specifies the HSRP group number on […]
Which protocol allows the network to fully use standby routers in a redundancy group without additional admini
Which protocol allows the network to fully use standby routers in a redundancy group without additional administrative burden? A. HSRP B. VRRP C. GLBP D. IRDP Explanation: Gateway Load Balancing Protocol (GLBP) allows the network to fully utilize standby routers in a redundancy group. Unlike HSRP and VRRP, GLBP allows automatic selection and simultaneous use […]
Which of the following commands should be included in the plan to meet the given requirements? (Choose all tha
You have been assigned to create a plan to implement HSRP on the router connecting your company’s network to the Internet. The router should be the active router in the HSRP group. On the active router, the following conditions should be met: ● Enable preemption with no delay ● Set Hello timer to 10 seconds […]
The partial output displayed in the exhibit is a result of what IOS command? (Click on the Exhibit(s) button.)
The partial output displayed in the exhibit is a result of what IOS command? (Click on the Exhibit(s) button.) A. switch# show running-config B. switch# show standby vlan1 active brief C. switch# show hsrp 1 D. switch# show standby Explanation: The command show standby produces the output displayed in the exhibit. This command displays information […]
What command should be executed on Router 1?
You have configured three routers in HSRP group 10 to provide gateway redundancy for VLAN 56. Your intention was for Router 1 to be the active router in the group and for Router 3 to be the standby router. Furthermore, in the event that Router 1 became unavailable, resulting in Router 3 becoming active, you […]
Assuming that preempt is not configured, when does a router in an HSRP group assume the role of the active rou
Assuming that preempt is not configured, when does a router in an HSRP group assume the role of the active router for the group? A. A router in standby status will become the active router if it has a higher priority than the active router. B. A router in standby status will become the active […]
What attack technique can be used to force user traffic through an attacking device, causing a man-in-the-midd
What attack technique can be used to force user traffic through an attacking device, causing a man-in-the-middle attack? A. VLAN hopping B. DHCP spoofing C. Rogue device D. MAC flooding Explanation: DHCP spoofing is an attack that can be used to force user traffic through an attacking device. This is accomplished by an attacker responding […]
Which of the following commands should be used on switch A to achieve the desired results?
You have configured switches A and B in a network. The gigabitethernet0/1 interface of switch A has HSRP enabled on it for VLAN 30. Switch A has a priority of 240 and switch B has a priority of 200 for the HSRP group. You want to ensure that if the gigabitethernet0/1 interface of switch A […]
What command would be used to display detailed information regarding VRRP groups on the switch?
What command would be used to display detailed information regarding VRRP groups on the switch? A. switch# show vrrp B. switch# show standby C. switch# show vrrp detail D. switch# show standby detail Explanation: The command that would display detailed information regarding VRRP groups on the switch is show vrrp. The information provided for each […]