What is the interaction between CDP, ISDP, and LLDP when communicating configuration information from a Dell E
What is the interaction between CDP, ISDP, and LLDP when communicating configuration information from a Dell EMC Campus networking switch to a Cisco VoIP phone? A. N-Series switches can be configured to use LLDP or CDP to communicate configuration information with Cisco devices B. N-Series switches can be configured to use only CDP to communicate […]
When configuring a Dell EMC N-Series switch for voice traffic, which settings are needed?
When configuring a Dell EMC N-Series switch for voice traffic, which settings are needed? A. Enable voice VLAN Set each-interface to LLDP share all VoIP related parameters Set switchport mode to general B. Create a VLAN for voice Set each interface to ISDP share all VoIP related parameters Set switchport mode to general C. Enable […]
If Client B sends a packet to Client A, what is the highest level of the network hierarchy that the packet wil
Refer to the Exhibit. If Client B sends a packet to Client A, what is the highest level of the network hierarchy that the packet will transverse? A. Distribution B. Network C. Access D. Core
What is the recommended maximum number of routers, per area, when using OSPF?
What is the recommended maximum number of routers, per area, when using OSPF? A. 50 B. 100 C. 200 D. 255
What is the IP protocol number, in decimal, assigned by IANA for VRRP?
What is the IP protocol number, in decimal, assigned by IANA for VRRP? A. 25 B. 112 C. 443 D. 1443
Based on this information, what is the Layer 3 QoS value?
After setting up the VoIP configuration, a network administrator issues the following commands with the results shown: console# show voice vlan Administrative Mode………………………Enable console# show voice vlan it gi 1/0/2 Interface………………………………….Gi1/0/2 Voice VLAN Interface Mode……………Enabled Voice VLAN ID………………………….10 Voice VLAN COS Overwrite……………False Voice VLAN DSCP Value……………….46 Voice VLAN Port Status…………………Enabled Voice VLAN Authentication………….…Disabled Based on […]
What additional steps need to be performed?
When setting up VoIP, you decide that you want to use LLDP. LLDP is enabled by default and LLDP Transmit Management Information and Notification modes are enabled. What additional steps need to be performed? A. Enable ISDP and enable LLDP-MED confignotification B. Disable ISDP and enable LLDP-MED confignotification C. Enable ISDP and disable LLDP-MED confignotification […]
Which access-list is preventing this traffic?
A user’s host with an IP address of 172.16.1.22/24 is attempting to FTP a file from the server with IP address 10.1.1.99; however, they are unable to connect. Which access-list is preventing this traffic? A. # ip access-list ACL1 # deny ip any host 10.1.1.99 B. # ip access-list ACL2 # permit ip 172.16.1.0 0.0.0.255 […]
When configuring a PBR route-map, what are the configurable “SET” options?
When configuring a PBR route-map, what are the configurable “SET” options? A. set ip source, set ip next-hop, and set ip default next-hop B. set ip next-hop, set ip source, and set ip precedence C. set ip next-hop, set ip default next-hop, and set ip precedence D. set ip source, set ip default next-hop and […]
Which command did the administrator fail to enter?
An administrator just finished configuring a Dell EMC N-Series switch. After rebooting the switch, the administrator notices that all the configuration settings just entered are gone. Which command did the administrator fail to enter? A. Copy running-config startup-config B. Copy running-config backup-config C. Copy startup-config backup-config D. Copy startup-config running-config