Where can the technician configure the LCD?
Before deploying a server, a customer needs a technician to configure the front panel LCD to display a custom message that contains the customer’s help desk phone number. However, the server cannot be rebooted. Where can the technician configure the LCD? A. Lifecycle Controller B. iDRAC web GUI C. System BIOS D. iSM
What troubleshooting steps should the technician take to resolve this issue?
A technician plugs in a server that has dual power supply units. After powering on the system, they notice that the power supply status indicators blink green then turn off. What troubleshooting steps should the technician take to resolve this issue? A. Set the power supply redundancy option to ‘No Redundancy’ B. Check that the […]
How should the technician obtain access to the remaining 2 TB (approximately) of storage?
A technician is creating a virtual disk in the DRAC (2x 4 TB NL-SAS in RAID 1) to install Windows 2016. They manually boot to the OS installation media without using the Lifecycle Controller OS Deployment wizard. Only the first 2048 GB on the virtual disk can be partitioned. How should the technician obtain access […]
A server is equipped with 2 CPUs and 12x 8 GB DIMMs, for a total of 96 GB. The OS is not seeing all the memory
A server is equipped with 2 CPUs and 12x 8 GB DIMMs, for a total of 96 GB. The OS is not seeing all the memory. Which memory mode should be configured so that all memory is seen by the OS? A. Mirroring B. Advanced ECC C. Optimizer D. Sparing Reference https://www.dell.com/support/article/pk/en/pkbsd1/sln155709/memory-modes-in-dual-processor-11th-generation-poweredge-servers?lang=en#Sparing
A technician needs to set a server to always attempt PXE boot before booting to the hard drive. What actions d
A technician needs to set a server to always attempt PXE boot before booting to the hard drive. What actions does the technician need to take to achieve this? A. Change the Boot Sequence so the network card is first Remove all boot options except network card B. Change the Boot Sequence so the network […]
What does the user need to consider?
A user has a fully configured PowerEdge R640 and an iSM installed on their Windows 2016 operating system. They now want to install OMSA to enable them to have alerts sent out in-Band to a management console. What does the user need to consider? A. OMSA can be installed on the same operating system with […]
What method can be used to enable the default login account?
A technician receives a repurposed PowerEdge server. After racking and cabling the server, the technician attempts to log into the iDRAC but cannot do so. The default account has been disabled. What method can be used to enable the default login account? A. Run the racadm recreset command from the host OS. B. Run the […]
A technician is installing a new server and is not getting any link lights on the iDRAC management port. They
A technician is installing a new server and is not getting any link lights on the iDRAC management port. They have verified that the cable and switch port are working. What could be causing this issue? A. iDRAC has an Express license B. IP has not been set in the Lifecycle Controller C. iDRAC has […]
What can a technician do to ensure that no malicious code can be introduced into any of the servers through ph
What can a technician do to ensure that no malicious code can be introduced into any of the servers through physical access? A. Set USB 3.0 to disabled B. Set Secure Boot Policy to enabled C. Set User Accessible Ports to disabled D. Set UEFI Variable Acces to disabled
A technician creates two virtual disks and assigns a dedicated hot spare to each virtual disk. They also creat
A technician creates two virtual disks and assigns a dedicated hot spare to each virtual disk. They also create a global hot spare. A drive fails on the second virtual disk. What is the result? A. Dedicated hot spare for the virtual disk replaces the failed drive. B. Global hot spare replaces the failed drive. […]