Scenario:
You have been asked by your customer to help resolve issues in their routed network. Their
network engineer has deployed HSRP. On closer inspection HSRP doesn’t appear to be operating
properly and it appears there are other network problems as well. You are to provide solutions to
all the network problems.
Examine the configuration on R4. The routing table shows no entries for 172.16.10.0/24 and
172.16.20.0/24. Identify which of the following is the issue preventing route entries being installed
on R4 routing table?
A.
HSRP issue between R4 and R2
B.
This is an OSPF issue between R4 and R2
C.
This is a DHCP issue between R4 and R2
D.
The distribute-list configured on R4 is blocking route entries
E.
The ACL configured on R4 is blocking inbound traffic on the interface connected to R2
Explanation:
If we look at the configuration on R4 we see that there is a distribute list applied to OSPF, which
blocks the 172.16.20.0/24 and 172.16.10.0/24 networks.
New 300-135 Questions(Updated on August/30/2017):
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1).
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: B
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1).
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. NTP
B. IPv4 OSPF Routing
C. IPv6 OSPF Routing
D. IPv4 layer 3 security
Answer: C
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1).
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to fault condition?
A. Under the interface Serial 0/0/0.23 configuration enter the ipv6 ospf 6 area 0 command.
B. Under the interface Serial0/0/0.12 configuration enter the ipv6 ospf 6 area 12 command.
C. Under ipv6 router ospf 6 configuration enter the network 2026::1:/122 area 0 command.
D. Under ipv6 router ospf 6 configuration enter no passive-interface default command.
Answer: A
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: E
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
The fault condition is related to which technology?
A. NTP
B. HSRP
C. IP DHCP Helper
D. IPv4 EIGRP Routing
E. IPv6 RIP Routing
F. IPv4 layer 3 security
G. Switch-to-Switch Connectivity
H. Loop Prevention
I. Access Vlans
Answer: B
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?
A. Under the interface vlan 10 configuration enter standby 10 preempt command.
B. Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.
C. Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.
D. Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.
Answer: D
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
On which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
E. DSW1
F. DSW2
G. ASW1
H. ASW2
Answer: D
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. Ipv4 OSPF Routing
D. Ipv4 EIGRP Routing.
E. Ipv4 Route Redistribution.
F. Ipv6 RIP Routing
G. Ipv6 OSPF Routing
H. Ipv4 and Ipv6 Interoperability
I. Ipv4 layer 3 security.
Answer: B
QUESTION
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
What is the solution to the fault condition?
A. Under the global configuration, delete the no ip dhcp use vrf connected command.
B. Under the IP DHCP pool configuration, delete the default -router 10.2.1.254 command and enter the
default-router 10.1.4.5 command.
C. Under the IP DHCP pool configuration, delete the network 10.2.1.0 255.255.255.0 command and
enter the network 10.1.4.0 255.255.255.0 command.
D. Under the IP DHCP pool configuration, issue the no ip dhcp excluded-address 10.2.1.1 10.2.1.253
command and enter the ip dhcp excluded-address 10.2.1.1 10.2.1.2 command.
Answer: D
QUESTION
On Which device is the fault condition located?
A. R1
B. R2
C. R3
D. R4
Answer: D
Detailed 300-135 Answers Explanation and more new 300-135 real exam questions: https://www.braindump2go.com/300-135.html (131Q&As Version)
0
0