How is a defective DIMM displayed in Dell EMC PowerStore Manager?
How is a defective DIMM displayed in Dell EMC PowerStore Manager? A. Orange with an empty state B. Blue with a faulted state C. Orange with a faulted state D. Blue with an empty state
What is the result of the network configuration shown for a Dell EMC PowerStore T?
Refer to the exhibit. What is the result of the network configuration shown for a Dell EMC PowerStore T? A. Interfaces are configured for remote replication traffic B. Interfaces are configured for PowerStore discovery traffic C. Ports 1/1/55 and 1/1/56 are added to a new LACP domain D. Ports 1/1/55 and 1/1/56 are added to […]
During Dell EMC PowerStore startup, both appliance nodes have rebooted in service mode. What must be done firs
During Dell EMC PowerStore startup, both appliance nodes have rebooted in service mode. What must be done first to avoid management software conflicts? A. Reboot node B B. Clear the boot mode C. Disable node B boot mode D. Return node A to normal mode Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-1000/pwrstr-isg/power-control-procedure-considerations?guid=guid-4352c94e-0ae7-4a2e-8593-9ae135bb9e34&lang=en-us
Which port is used to SSH from one Dell EMC PowerStore appliance to another?
Which port is used to SSH from one Dell EMC PowerStore appliance to another? A. 22 B. 26 C. 443 D. 21 Reference: https://topics-cdn.dell.com/pdf/pwrstr-scg_en-us.pdf
A Storage Administrator needs to connect through SSH to run svc commands. How is the SSH session configured?
A Storage Administrator needs to connect through SSH to run svc commands. How is the SSH session configured? A. Appliance IP address using port 22 B. NAS server IP address using port 26 C. NAS server IP address using port 22 D. Appliance IP address using port 26
They observe that the base enclosure LED circled is blue. What does this indicate?
Refer to the exhibit. A Storage Administrator is troubleshooting a Dell EMC PowerStore T hardware issue. They observe that the base enclosure LED circled is blue. What does this indicate? A. Base enclosure hardware is operating normally B. Base enclosure has a component hardware fault C. Cluster has only a single appliance D. Appliance has […]
What is the last step when adding a drive to a Dell EMC PowerStore system?
What is the last step when adding a drive to a Dell EMC PowerStore system? A. Verify the new drive is seen B. Add the drive to the pool C. Backup the keystore D. Zero the drive Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/install-a-25-drive?guid=guid-bddae51e-a561-4e84-bc0a-c2e99a43f033&lang=en-us
What describes the power requirements for Dell EMC PowerStore?
What describes the power requirements for Dell EMC PowerStore? A. Lower model numbered systems require less AC line current than higher model numbered systems B. T models require less total power than X models C. X models require less total power than T models D. Lower model numbered systems require less input voltage (VAC) than […]
What is different about the management network configuration for the new appliance compared to configuring an
A Storage Administrator is adding an appliance into an existing Dell EMC PowerStore T cluster. What is different about the management network configuration for the new appliance compared to configuring an initial appliance for the cluster? A. All the needed management IP addresses for the new appliance must be pre-configured on the cluster B. Additional […]
Through which network do external hosts connect to the cluster for data access?
Through which network do external hosts connect to the cluster for data access? A. Management B. ICM C. ICD D. Storage Reference: https://topics-cdn.dell.com/pdf/pwrstr-hcg_en-us.pdf