Examine the following partial output of the show interfaces command.
Router# show interfaces ethernet 0/0
Ethernet0/0 is administratively down, line protocol is down
Hardware is AmdP2, address is 0003.e39b.9220 (bia 0003.e39b.9220)
Internet address is 10.1.0.254/16
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
<<output omitted>>

Which of the following statements are true? (Choose all that apply.)

What command was used to generate the output shown below?
Connection-specific DNS Suffix . : ajax.acme.com
Description . . . . .. . .: Broadcom NetXtreme 57xx Gigabit Controller
Physical Address. . . . . . . . : 00-1A-A0-E1-95-AB
DHCP Enabled. . . . . . . . . . : Yes
Autoconfiguration Enabled . . . : Yes
Link-local IPv6 Address . : fe80::ada3:8b73:a66e:6bc0%10(Preferred)
IPv4 Address. . . . . . . . . . : 10.88.2.177(Preferred)
Subnet Mask . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . .. : Wednesday, October 05, 2011 4:31:32 PM
Lease Expires . . . . . . . : Friday, October 07, 2011 4:33:32 AM
Default Gateway . . . . . . . . : 10.88.2.6
DHCP Server . . . . . . . . . . : 10.88.10.48
DHCPv6 IAID . . . . . . . . . . : 234887840
DHCPv6 Client DUID. . . : 00-01-00-01-14-EE-0F-98-00-1A-A0-E1-95-AB
DNS Servers . . . . . . . . . . . : 10.88.10.48
10.75.139.18
NetBIOS over Tcpip. . . . . . . . : Enabled

The conference room has a switch port available for use by the presenter during classes. You would liketo prevent that port from hosting a hub or switch. Which of
the following commands could be used to prevent that port from hosting a hub or switch?

You have successfully configured a router, but it prompts you to run Setup mode every time the router is restarted. Based on the following output, what could be
causing this problem?
RouterA# show version
Cisco Internetwork Operating System SoftwareIOS ™ 2500 Software (C2500-JS-L), Version 11.3(6), RELEASE SOFTWARE (fc1)
Copyright 1986-1998 by Cisco Systems, Inc.
Compiled Tue 06-Oct-98 22:17 by kpma
Image text-base: 0x03048CF4, data-base: 0x00001000
ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE SOFTWARE (fc1)
RouterA uptime is 25 minutes
System restarted by power-on
System image file is “flash:c2500-js-l_113-6.bin”, booted via flash
Cisco 2500 (68030) processor (revision D) with 4096K/2048K bytes of memory.
Processor board ID 04203139, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
2Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2142

Which feature enables a host to obtain an IP address from a DHCP server on another subnet?

You need to manually assign IPv6 addresses to the interfaces on an IPv6-enabled router. While assigning addresses, you need to ensure that the addresses
participate in neighbor discovery and in stateless auto-configuration process on a physical link.
Which of the following addresses can be assigned to the interfaces?

RouterA and RouterB, which connect two locations, are unable to communicate. You run the show running-configuration command on both router interfaces,
RouterA and RouterB. The following is a partial output:
routerA#show running-config
interface Serial0
description Router_A
ip address 192.10.191.2 255.255.255.0
encapsulation ppp
no ip mroute-cache
clockrate 64000
routerB#show running-config
interface Serial1
description Router_B
ip address 192.10.192.1 255.255.255.0
encapsulation ppp
no ip mroute-cache
clockrate 64000
Based on the information given in the output, what are two likely causes of the problem? (Choose two.)

Which type of IP address is a registered IP address assigned by the Internet Service Provider (ISP), and represents one or more inside local IP addresses
externally?

You are the network administrator for your company. You wanted to connect the host computers to the switches.
Which cable should you use to ensure the connectivity?

Which feature is NOT provided by flow control?