What is the difference between AAL5 SNAP and AAL5 MUX virtual circuits?
What is the difference between AAL5 SNAP and AAL5 MUX virtual circuits?
what is the subscriber’s trouble symptom?
The following configuration is from a Cisco DSLAM:interface ATM1/1no ip addressdsl profile basicno atm ilmi-keepaliveatm pvc 2 32 interface ATM0/1 1 32This configuration is from a Cisco 2600 router with an ADSL WIC installed:interface ATM0/0.1 point-to-pointip address 192.168.1.2 255.255.255.0pvc 1/32protocol ip 192.168.1.1 broadcastencapsulation aal5snapThe CPE is connected to DSLAM DSL port 1/1 via a DSL line. The subscriber’s DSL service is not working correctly. Based on the information shown in these two “show run” output messages, what is the subscriber’s trouble symptom?
What ATM Adaptation Layer is used when an ATM cell carries IP packets and PPP frames?
ATM carries IP and PPP information within ATM cells. What ATM Adaptation Layer is used when an ATM cell carries IP packets and PPP frames?
All of the following are components of LANE except:
All of the following are components of LANE except:
What is the use of a VC class in IOS configuration?
What is the use of a VC class in IOS configuration?
Which one of the following presented choices is clearly the most appropriate information needed to begin troub
A subscriber complains that his DSL rates are slower than the service he ordered. The customer ordered ADSL at 1 mpbs downstream and 256 kbps upstream, but the maximum bitrate observed during file downloads is never more than 128 kbps downstream. Initial troubleshooting shows that the subscriber’s DSL modem is trained at 1024 kbps downstream and 256 kbps upstream. Which one of the following presented choices is clearly the most appropriate information needed to begin troubleshooting the problem?
what command?
The following message is from a Cisco DSLAM:Status:Bitrates:Interleave Path: downstream: 2048 kb/s, upstream: 256 kb/sFast Path: downstream: 0 kb/s, upstream: 0 kb/sMargin: downstream: 18 dB, upstream: 22 dBAttenuation: downstream: 30 dB, upstream: 20 dBInterleave Delay: downstream: 16000 usecs, upstream: 16000 usecsTransmit Power: downstream: 16.0 dB, upstream: 0.0 dBCheck Bytes (FEC):Interleave Path: downstream: 16, upstream: 16Fast Path:
downstream: 0, upstream 0R-S Codeword Size: downstream: 1, upstream: 8Trellis Coding: Not In UseOverhead Framing: Mode 3Operating Mode: ANSI T1 413 Issue 2Line Type: Interleaved OnlyThis information was presented as a result of what command?
The ATM Transmission Convergence Sublayer is NOT responsible for:
The ATM Transmission Convergence Sublayer is NOT responsible for:
What will the encapsulation type for the PVCs be?
The following configuration is entered on an ATM interface:interface atm 0/0/0encapsulation aal5mux ppp virtual-template 1interface atm 0/0/0.10 multipointpvc 0/100exitpvc 0/101encapsulation aal5snapWhat will the encapsulation type for the PVCs be?
Find the problem in the following configuration:
Find the problem in the following configuration:vpdn enablevpdn-group 1request-dialinprotocol pppoevirtual-template 2!interface atm 2/0.1 point-to-pointpvc 0/101encapsulation aal5snapprotocol pppoe!interface atm 2/0.2 point-to-pointpvc 0/102encapsulation aal5snapprotocol pppoe!interface atm 2/0.3 point-to-pointpvc 0/103encapsulation aal5snapprotocol pppoe!interface virtual-template 2ip unnumbered Fastethernet 4/0!interface FastEthernet 4/0ip address 172.22.32.1 255.255.255.0