What is the VLAN status of SW2 after the reboot?
Refer to the exhibit.
The Cisco IOS Software-based switches are configured with VTP and VLANs as shown. The network administrator wants to quickly add the VLANs defined on SW1 to the configuration of SW2. Therefore, the administrator copies the vlan.dat file from the flash memory on SW1 to the flash memory of SW2. After the file is copied to SW2, it is rebooted. What is the VLAN status of SW2 after the reboot?
Which three of these situations warrant engagement of a Security Incident Response team?
Which three of these situations warrant engagement of a Security Incident Response team? (Choose three.)
Which feature can the customer enable to help resolve this?
A customer has Cisco IOS Firewall deployed. Even though the customer has FTP inspection enabled, inspection does not appear to be working for FTP services running on a non-standard port of 21000. Which feature can the customer enable to help resolve this?
Which two MQC actions are supported in policy maps?
The Control Plane Policing (CoPP) feature allows users to configure a quality of service (QoS) filter that manages the traffic flow of control plane packets. The filter protects the control plane of Cisco IOS devices against reconnaissance and denial of service (DoS) attacks. The Control Plane Policing feature requires the Modular Quality of Service (QoS) Command-Line interface (CLI) (MQC) to configure packet classification and policing. Which two MQC actions are supported in policy maps?
which three of these features?
A Cisco ASA adaptive security appliance configured in multiple context mode supports which three of these features? (Choose three.)
what must be done?
Prior to installing the Cisco IOS IPS version 5.0 signature package on a router for the first time, what must be done?
How would the router treat a packet with a destination address of 192.168.1.63?
A router has this configuration on one of its interfaces:
interface FastEthernet0/0
ip address 192.168.1.33 255.255.255.224
end
How would the router treat a packet with a destination address of 192.168.1.63?
Which three of these could be reasons?
You configured two routers for EBGP, but you see your BGP neighbor’s state is Active after issuing the show ip bgp neighbor command. Which three of these could be reasons? (Choose three.)
which of these?
You have configured a DMVPN hub and spoke as follows (assume the IPsec profile “dmvpnprofile” is configured correctly):
Hub:
interface Tunnel0
ip address 172.16.1.1 255.255.255.0
no ip redirects
ip nhrp authentication cisco
ip nhrp map multicast dynamic
ip nhrp network-id 10
ip nhrp holdtime 600
ip nhrp redirect
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 10000
tunnel protection ipsec profile dmvpnprofile
Spoke 1:
interface Tunnel0
ip address 172.16.1.2 255.255.255.0
no ip redirects
ip nhrp authentication cisco
ip nhrp map multicast 1.1.1.2
ip nhrp map 172.16.1.1 1.1.1.2
ip nhrp network-id 20
ip nhrp holdtime 300
ip nhrp nhs 172.16.1.1
ip nhrp shortcut
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 1000
tunnel protection ipsec profile dmvpnprofile
With this configuration, you notice that the IKE and IPsec SAs come up between the spoke and the hub, but NHRP registration fails. Registration will continue to fail until you do which of these?
which of the following was the administrator able to determine?
Refer To the Exhibit.
A company just completed the rollout of IP/TV. The first inside network multicast client to use the new feature claims that they cannot access the service. After reviewing the above ASA security appliance configuration and network diagram, which of the following was the administrator able to determine?