Which of the following features does GLBP provide, but not HSRP and VRRP? (Choose all that apply.)
Which of the following features does GLBP provide, but not HSRP and VRRP? (Choose all that apply.) A. Support for single active router B. Support for automatic load balancing C. Support for multiple gateways D. Support for interface tracking Explanation: Support for automatic load balancing and support for multiple gateways are two features that are […]
What command would provide the output displayed in the exhibit? (Click on the Exhibit(s) button.)
What command would provide the output displayed in the exhibit? (Click on the Exhibit(s) button.) A. switch# show hsrp B. switch# show standby C. switch# show interface vlan D. switch# show standby brief Explanation: The command show standby brief displays the output in the exhibit. It is used to display a summary of the HSRP […]
Which of the following routers were configured with the default HSRP values for each command?
Refer to the following exhibit: You have configured the routers in the diagram for HSRP, resulting in the displayed configurations. Which of the following routers were configured with the default HSRP values for each command? A. rtrA B. rtrB C. rtrC D. rtrD Explanation: Only rtrB has the default HSRP settings. The default values for […]
Which load-balancing algorithm does GLBP use by default?
Which load-balancing algorithm does GLBP use by default? A. Random load-balancing B. Weighted load-balancing C. Round-robin load-balancing D. Host-dependent load-balancing Explanation: Round-robin load-balancing is the default load-balancing method used by Gateway Load Balancing Protocol (GLBP). The active virtual gateway (AVG) can be configured to use one of three load-balancing algorithms when selecting which active virtual […]
Which of the following statements best describes the result of issuing the command standby 44 timers 3 1 on an
Which of the following statements best describes the result of issuing the command standby 44 timers 3 1 on an HSRP router? A. The holdtime will be set to a value of 3, and the hellotime will be set to a value of 1. B. The status of the standby router will be displayed as […]
Which statement best describes the function of Hot Standby Router Protocol (HSRP)?
Which statement best describes the function of Hot Standby Router Protocol (HSRP)? A. HSRP specifies a single IP address that all routers in the group must use. B. HSRP defines a set of routers that represent one virtual, fault-tolerant router. C. HSRP provides a round-robin gateway selection process to increase fault tolerance. D. HSRP defines […]
The output displayed below is a result of what command?
The output displayed below is a result of what command? Interface Grp Fwd Pri State Address Active router Standby router Vl10 10 – 254 Active 192.168.8.10 local unknown Vl10 10 1 7 Active 0007.b400.0101 local – A. switch# show standby B. switch# show glbp C. switch# show standby brief D. switch# show glbp brief Explanation: […]
Which command enables HSRP on an interface?
Which command enables HSRP on an interface? A. hsrp B. standby ip C. standby mode hsrp D. switchport mode hsrp Explanation: The standby ip interface configuration command enables Hot Standby Router Protocol (HSRP). The syntax for this command is as follows: switch(config-if)# standby group-number ip ip-address The group-number argument specifies the HSRP group number on […]
Which protocol allows the network to fully use standby routers in a redundancy group without additional admini
Which protocol allows the network to fully use standby routers in a redundancy group without additional administrative burden? A. HSRP B. VRRP C. GLBP D. IRDP Explanation: Gateway Load Balancing Protocol (GLBP) allows the network to fully utilize standby routers in a redundancy group. Unlike HSRP and VRRP, GLBP allows automatic selection and simultaneous use […]
Which of the following commands should be included in the plan to meet the given requirements? (Choose all tha
You have been assigned to create a plan to implement HSRP on the router connecting your company’s network to the Internet. The router should be the active router in the HSRP group. On the active router, the following conditions should be met: ● Enable preemption with no delay ● Set Hello timer to 10 seconds […]