Which of the following features work the same in both RIP-2 and RIPng? (Choose three.)

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration
exists in a planning document, intended to be used to copy/paste into
Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related
configuration exists. Which of the following is true about RIPng on R1 after this configuration
has been pasted into R1?
ipv6 unicast-routing
interface f0/0
ipv6 rip one enable
ipv6 address 2000::1/64
interface s0/0/0
ipv6 address 2001::/64 eui-64
ipv6 rip one enable

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration
exists in a planning document intended to be used to copy/paste into
Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related
configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following
is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?
ipv6 router eigrp 1
ipv6 unicast-routing
interface f0/0

ipv6 address 2000::1/64
ipv6 eigrp 1
interface s0/0/0
ipv6 address 2001::/64 eui-64
ipv6 eigrp 1

Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0
interfaces. R1 learns a route from R2 using EIGRP for IPv6. That route lists F0/0 as the
outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant
configuration on R2’s F0/0 interface. Which of the following is true about R1’s route?
interface f0/0
mac-address 1111.1111.1111
ipv6 address 2000::/64 eui-64
ipv6 address 2001::1/64

Which of the following are true of both OSPFv2 and OSPFv3? (Choose two.)

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration
exists in a planning document, intended to be used to copy/paste into
Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration
exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about
OSPFv3 on R1 after this configuration has been pasted into R1?
ipv6 router ospf 1
ipv6 unicast-routing
interface f0/0
ipv6 address 2000::1/64
ipv6 ospf 1 area 1
interface s0/0/0
ipv6 address 2001::/64 eui-64
ipv6 ospf 1 area 0

The following output occurs on Router R1, which runs both EIGRP for IPv6 and OSPFv3,
with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25
command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following
should be true of redistribution in this case?
D 2000::/64 [90/1422516]
via FE80::213:19FF:FE7B:5026, Serial0/0/1
C 2000:0:0:1::/64 [0/0]
via Serial0/0/1, directly connected
L 2000::1:213:19FF:FE7B:5004/128 [0/0]
via Serial0/0/1, receive

Router R1 has been configured with an ipv6 route 2000::/64 S0/0/0 64 command.
Which of the following does the 64 at the end of the command represent?

An enterprise has plans to start adding IPv6 support. For the first year, the IPv6 will be in
small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic
while applications teams test IPv6-enabled servers and applications. Which of the following
tools would be most appropriate?

An enterprise has plans to start adding IPv6 support. The initial deployment requires support
from some IPv6-only devices that need to access servers that support only IPv4. Which of
the following tools would be most appropriate?