Drag the steps on the left and arrange them in the order they should be completed when removing an industrial
DRAG DROP
Drag the steps on the left and arrange them in the order they should be completed when removing an industrial switch from a DIN rail on the right.
Which command should be used to create this map?
A static map to the S-AMER location is required. Which command should be used to create this
map?
Which three are components of a dial plan?
Which three are components of a dial plan? (Choose three.)
Why are the interfaces missing?
Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links.
R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also
connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
The loopback interfaces on R4 with the IP addresses of 10.4.4.4 /32, 10.4.4.5/32. and 10.4.4.6/32
are not appearing in the routing table of R5 Why are the interfaces missing?
Which path does traffic take from R1 to R5?
Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links.
R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also
connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
Which path does traffic take from R1 to R5?
What is the cause for this misconfiguration?
Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links.
R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also
connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
Router R6 does not form an EIGRP neighbor relationship correctly with router R1. What is the
cause for this misconfiguration?
Which type of voice port will terminate a loop start or ground start line from the PSTN or a PBX?
Which type of voice port will terminate a loop start or ground start line from the PSTN or a PBX?
Why are the pings failing?
Scenario
Refer to the topology. Your company has connected the routers R1. R2. and R3 with serial links.
R2 and R3 are connected to the switches SW1 and SW2, respectively. SW1 and SW2 are also
connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
Study the following output taken on R1:
R1# Ping 10.5.5.55 source 10.1.1.1
Type escape sequence to abort.
Sending 5.100-byte ICMP Echos to 10.5.5.55, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
Why are the pings failing?
Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is
Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic
environment that is classified as M3 I3 C3 E3?
IP information
CORRECT TEXT
Attention:
In practical examinations, please note the following, the actual information will prevail.
1. Name of the router is xxx
2. Enable secret password is xxx
3. Password In access user EXEC mode using the console is xxx
4. The password to allow telnet access to the router is xxx
5. IP information