Find the problem in the following configuration:
Find the problem in the following configuration:vpdn enablevpdn-group 1request-dialinprotocol pppoevirtual-template 2!interface atm 2/0.1 point-to-pointpvc 0/101encapsulation aal5snapprotocol pppoe!interface atm 2/0.2 point-to-pointpvc 0/102encapsulation aal5snapprotocol pppoe!interface atm 2/0.3 point-to-pointpvc 0/103encapsulation aal5snapprotocol pppoe!interface virtual-template 2ip unnumbered Fastethernet 4/0!interface FastEthernet 4/0ip address 172.22.32.1 255.255.255.0
All of the following are components of LANE except:
All of the following are components of LANE except:
What is the use of a VC class in IOS configuration?
What is the use of a VC class in IOS configuration?
what command?
The following message is from a Cisco DSLAM:Status:Bitrates:Interleave Path: downstream: 2048 kb/s, upstream: 256 kb/sFast Path: downstream: 0 kb/s, upstream: 0 kb/sMargin: downstream: 18 dB, upstream: 22 dBAttenuation: downstream: 30 dB, upstream: 20 dBInterleave Delay: downstream: 16000 usecs, upstream: 16000 usecsTransmit Power: downstream: 16.0 dB, upstream: 0.0 dBCheck Bytes (FEC):Interleave Path: downstream: 16, upstream: 16Fast Path:
downstream: 0, upstream 0R-S Codeword Size: downstream: 1, upstream: 8Trellis Coding: Not In UseOverhead Framing: Mode 3Operating Mode: ANSI T1 413 Issue 2Line Type: Interleaved OnlyThis information was presented as a result of what command?
What will the encapsulation type for the PVCs be?
The following configuration is entered on an ATM interface:interface atm 0/0/0encapsulation aal5mux ppp virtual-template 1interface atm 0/0/0.10 multipointpvc 0/100exitpvc 0/101encapsulation aal5snapWhat will the encapsulation type for the PVCs be?
Which three of these are properties of Encapsulating Security Payload (ESP) protocol (in non- tunnel model?
Which three of these are properties of Encapsulating Security Payload (ESP) protocol (in non- tunnel model? (Choose three)
What is the difference between AAL5 SNAP and AAL5 MUX virtual circuits?
What is the difference between AAL5 SNAP and AAL5 MUX virtual circuits?
what is the subscriber’s trouble symptom?
The following configuration is from a Cisco DSLAM:interface ATM1/1no ip addressdsl profile basicno atm ilmi-keepaliveatm pvc 2 32 interface ATM0/1 1 32This configuration is from a Cisco 2600 router with an ADSL WIC installed:interface ATM0/0.1 point-to-pointip address 192.168.1.2 255.255.255.0pvc 1/32protocol ip 192.168.1.1 broadcastencapsulation aal5snapThe CPE is connected to DSLAM DSL port 1/1 via a DSL line. The subscriber’s DSL service is not working correctly.
Based on the information shown in these two “show run” output messages, what is the subscriber’s trouble symptom?
what is true?
The following is an excerpt from a “show run” display in a Cisco DSLAM.interface ATM1/1no ip addressatm clock INTERNALno atm ilmi-keepaliveatm soft-vc 2 32 dest-address 47.0091.8100.0000.0030.949c.0b81.4000.0c80.8000.00 4 100Referring to this output message, what is true?
What is the purpose of rate decoupling for ATM transmission?
What is the purpose of rate decoupling for ATM transmission?