Which of the following three commands could be configured on each router to correct this problem?
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF between them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem? (Choose three.)
Select 3 response(s).
What is the effect of the OSPF configuration on router B?
Refer to the exhibit. What is the effect of the OSPF configuration on router B?
Select the best response.
What can you conclude from the exhibit and the show running-configuration command output?
RouterA#
~~~~~
!
router ospf 1
log-adjacency-changes
network 10.0.0.0 0.255.255.255 area 1
network 172.16.1.0 0.0.0.255 area 1
!
~~~~~
RouterB#
~~~~~
router ospf 1
log-adjacency-changes
network 10.0.0.0 0.255.255.255 area 2
network 172.16.2.0 0.0.0.255 area 2
!
~~~~~
RouterC#
~~~~~
!
router ospf 1
log-adjacency-changes
network 10.0.0.0 0.255.255.255 area 0
!
~~~~~
Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly.
What can you conclude from the exhibit and the show running-configuration command output?
Select the best response.
What is the probable cause of the problem?
Refer to the exhibits. Router B should advertise the network connected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B.
What is the probable cause of the problem?
Select the best response.
Which statement about dynamic routing protocols for this network is true?
Refer to the exhibit. Which statement about dynamic routing protocols for this network is true?
Select the best response.
Which action will accomplish this goal?
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network.
Which action will accomplish this goal?
Select the best response.
what feature can be used to ensure that routers C through F are not used as transit routers
Refer to the exhibit. In a redundant hub-and-spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0?
Select the best response.
Which two additions to the router B1 configuration should the engineer make?
Refer to the exhibit. A new TAC engineer comes to you for advice. The engineer wants to configure RIPv2-OSPF two-way redistribution while avoiding routing loops.
Which two additions to the router B1 configuration should the engineer make? (Choose two.)
Select 2 response(s).
which eBGP configurations would you configure in AS100 to influence AS200 to use the eBGP links more evenly?
Refer to the exhibit. Currently the two eBGP links between AS100 and AS200 have an average inbound load of 65% and 20% respectively. After further investigation, traffic to 10.10.1.16/28 accounts for 45%, and traffic to 10.10.1.32/28 and to 10.10.1.48/28 each account for 20% of the inbound load. The BGP attributes are currently set at their default values in both autonomous systems.
If you want to influence how AS200 sends traffic to AS100, which eBGP configurations would you configure in AS100 to influence AS200 to use the eBGP links more evenly? (Choose two.)
Select 2 response(s).
What did the TAC engineer configure incorrectly?
Refer to the exhibit. A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up.
What did the TAC engineer configure incorrectly?
Select the best response.