One Comment on “which two fields are required to successfully create a …”

1. Ramon109109 says:

   November 27, 2017 at 4:53 am

   QUESTION
   Which Cisco Unified Communications Manager device report provides key information to determine if an additional gateway is needed?

   A. Gateway utilization
   B. Gateway summary
   C. Gateway detail
   D. Gateway and line group utilization

   Answer: A

   QUESTION
   Which four tasks does RTMT allow an administrator to perform? (Choose four.)

   A. View syslog messages.
   B. Generate alerts when threshold is below or above user-configured.
   C. Monitor a set of predefined management objects that monitor the health of the system.
   D. Collect information and traces about errors or alerts that exist in the RTMT.
   E. Reboot the system.
   F. Perform incremental backups.
   G. Export CDR.

   Answer: ABCD

   QUESTION
   Which server does Cisco recommend that you configure before a CUCM backup?

   A. SFTP
   B. FTP
   C. SNMP
   D. TFTP

   Answer: A

   QUESTION
   What is the interface type that you should use to connect a PSTN analog line to the VoIP network?

   A. FXS
   B. FXO
   C. E and M
   D. Serial

   Answer: B

   QUESTION
   Which command is used to troubleshoot calls as they enter and leave a PRI connection?

   A. Debug isdn q 931
   B. Show voice call summary
   C. Debug voip dialpeer
   D. Show dial-peer voice summary

   Answer: A

   QUESTION
   Which configuration causes PSTN users to experience a fail tone for every other call when trying to reach a particular number on Cisco Unified CME?

   A. ephone-dn is not assigned to the ephone.
   B. Duplicate ephone-dn is not assigned to the ephone.
   C. ephone is not registered.
   D. ephone does not exist for the ephone-dn.

   Answer: B

   QUESTION
   Which Cisco Unified Communications Manager configuration causes an IP phone screen to display a “registration rejected” message?

   A. Cisco Unified Communications Manager is unable to reach user IP phone.
   B. Cisco Unified Communications Manager database replication status is 2.
   C. Cisco Unified Communications Manager auto registration is disabled.
   D. Cisco Unified Communications Manager is unable to allocate DN.
   E. Cisco Unified Communications Manager subscriber is offline.

   Answer: D

   QUESTION
   Customer requirements dictate that local calls from area code 408 display the ANI as a 7-digit number.
   Which procedure allows the leading digits to be stripped as soon as they arrive at the H.323 voice gateway?

   A. Set up a voice translation rule, apply the translation rule to a translation profile, and apply
   the translation profile to the dial peer in the inbound direction.
   B. Set up a voice translation profile, apply the translation profile to a translation rule, and apply
   the translation rule to the dial peer in the outbound direction.
   C. Set up a voice translation rule, apply the translation rule to a translation profile, and apply
   the translation profile to the dial peer in the outbound direction.
   D. Set up a voice translation profile, apply the translation profile to a translation rule, and apply
   the translation rule to the dial peer in the inbound direction.

   Answer: A

   QUESTION
   An end user has made more attempts to log in than allowed, using the wrong voice-mail pin.
   The user has been locked out.
   Which submenu does an administrator select to unlock the pin?

   A. Change password
   B. Password settings
   C. Message settings
   D. Mailbox

   Answer: B

   QUESTION
   Which three methods can remotely force a Cisco Unified Communications Manager Express phone to reset? (Choose three.)

   A. Issue a shutdown, no shutdown command on a switch port that provides PoE to a Cisco
   phone.
   B. Issue the restart command under the ephone-dn configuration of the phone.
   C. Issue the reset command under the ephone configuration of the phone.
   D. Issue the reset command under the ephone-dn configuration of the phone.
   E. Issue the reset H.H.H (mac-address) command telephony-service configuration.
   F. Issue the reset H.H.H (mac-address) command under global configuration.

   Answer: ACE

   More: https://www.braindump2go.com/210-065.html

   
   
   
   0

   
   
   
   0