One Comment on “Which three conditions can occur when metering traffic using a dual token bucket traffic policing QoS mechanis”

1. Chadwick Thomas says:

   August 25, 2017 at 9:02 pm

   Hello guys, passed 642-887 exam today in US. Uh, not so difficult as others said! I studied the 137q&as pdf and vce dumps: https://www.braindump2go.com/642-887.html , this file covers all new questions from the official test center. 87% Valid for exam passing. Some new questions i got in my test:
   QUESTION
   When configuring class-based WRED on Cisco routers, which WRED parameter is not user
   configurable on a Cisco IOS XR but is user configurable on a Cisco IOS and IOS XE?
   A. the ingress or egress direction where the class-based WRED policy will be applied
   B. the maximum threshold
   C. the minimum threshold
   D. the mark probability denominator
   Answer: D

   QUESTION
   Which of the following three statements are correct regarding IPv6 QoS? (Choose three.)
   A. The traffic class field in the IPv6 header can be used to set specific precedence or DSCP values.
   B. A 20-bit flow label field enables per-flow processing.
   C. DS-TE is not supported by IPv6.
   D. Per-hop behavior in IPv6 networks is based on EXP bits.
   E. IPv6 QoS features are configured using the modular QoS CLI on Cisco routers.
   Answer: ABE

   QUESTION
   With unmanaged CE routers, at which point in the service provider network is the QoS trust
   boundary, and what is required at the trust boundary?
   A. between the CE and PE router and mapping of the customer traffic classes into the service
   provider traffic classes at the PE router ingress
   B. between the CE and PE router and trusting the QoS markings from the CE router and
   applying the required QoS mechanisms based on the customer QoS markings
   C. between the PE and the P router and mapping of the customer traffic classes into the service
   provider traffic classes at the P router ingress
   D. between the PE and P router and trusting the QoS markings from the CE router and applying
   the required QoS mechanisms based on the customer QoS markings
   E. between the customer network and the CE router ingress and applying the required egress
   QoS policy on the CE router
   Answer: A

   QUESTION
   On the Cisco IOS XR, when using the match protocol command within a class-map to classify
   traffic, you noticed that the match protocol option on the Cisco IOS XR shows much fewer
   protocol options than on the Cisco IOS or IOS XE, like there is no option such as the match
   protocol yahoo-messenger command on the Cisco IOS XR. Why is this?
   A. because the Cisco IOS XR router does not have the correct software packages installed
   B. because when defining the class-map, the class-map type should be set to type inspect:
   class- map type inspect class-map-name command
   C. because NBAR is not supported on the Cisco IOS XR
   D. because flexible packet matching has not been enabled on the Cisco IOS XR router
   Answer: C

   QUESTION
   Within the service provider core network, which two QoS mechanisms are typically deployed on
   the P routers? (Choose two.)
   A. LLQ
   B. traffic policing and remarking
   C. WRED
   D. traffic shaping
   E. traffic classification and markings
   F. link fragmentation and interleaving
   Answer: AC

   QUESTION
   Which three steps are required to configure QPPB on Cisco IOS XR routers? (Choose three.)
   A. Apply a QPPB route policy to the BGP process using the table-policy command
   B. Apply a QPPB route policy to the BGP neighbor using the route-policy command
   C. Define a QPPB route policy to match the customer routes, then set the IP precedence or qosgroup
   D. Define a QPPB route policy to match the customer IP precedence or qos-group markings,
   then set the BGP community
   E. Enable QPPB on an interface using the ipv4 bgp policy propagation input ip-precedence|qosgroup
   destination|source command
   F. Enable QPPB on an interface using the ipv4 bgp policy propagation output ipprecedence|qos-
   group destination|source command
   Answer: ACE

   QUESTION
   The Cisco IOS and IOS XE qos pre-classify command allows which kind of packet classification
   on IP packets that are encapsulated with GRE and IPsec?
   A. allows for packets to be classified based on the ToS byte values before packet encryption
   B. allows for packets to be classified based on the ToS byte values after packet encryption
   C. allows for packets to be classified based on the packet payload before packet encryption
   D. allows for packets to be classified based on the packet payload after packet encryption
   E. allows for packets to be classified based on the packet header parameters other than the ToS
   byte values after packet encryption
   Answer: E

   QUESTION
   Which are typical class-based marking policies that are implemented on service provider IP NGN
   PE routers?
   A. On the PE ingress, classify the customer traffic and then mark with qos-group. On the PE
   egress, classify based on the qos-group and then mark with mpls exp.
   B. On the PE ingress, classify the customer traffic and then mark with mpls exp. On the PE
   egress, classify based on the mpls exp and then mark with qos-group.
   C. On the PE ingress, trust the customer QoS markings. On the PE egress, classify based on the
   customer QoS markings and then mark with qos-group.
   D. On the PE ingress, trust the customer QoS markings. On the PE egress, classify based on the
   customer QoS markings and then mark with mpls exp.
   Answer: A

   Wish all of you also can pass successfully!

   
   
   
   0

   
   
   
   0