You have noticed a large number of topology changes in the Rapid Spanning Tree Protocol
network. Which statement is true about RSTP topology changes?

Refer to the exhibit.

The link between switch SW1 and switch SW2 is configured as a trunk, but the trunk failed to
establish connectivity between the switches. Based on the configurations and the error
messages received on the console of SW1, what is the cause of the problem?

When you create a network implementation for a VLAN solution, what is one procedure that
you should include in your plan?

DRAG DROP
Syslog information can generate messages up to and including the configured severity level.
Organize levels by dragging each name from the left to the right.
Put the highest level at the top and the lowest level at the bottom?

DRAG DROP
Drag the choices on the left to the boxes on the right that should be included when creating a VLAN-based implementation plan. Not all choices will be used.

DRAG DROP

You have been tasked with planning a VLAN solution that will connect a server in one building several hosts in another building.

HOTSPOT

SIMULATION
Scenario:
You work for SWITCH.com. They have just added a new switch (SwitchB) to the existing
network as shown in the topology diagram.
RouterA is currently configured correctly and is providing the routing function for devices on
SwitchA and SwitchB. SwitchA is currently configured correctly, but will need to be modified
to support the addition of SwitchB. SwitchB has a minimal configuration. You have been
tasked with competing the needed configuring of SwitchA and SwitchB. SwitchA and
SwitchB use Cisco as the enable password.
Configuration Requirements for SwitchA
The VTP and STP configuration modes on SwitchA should not be modified.
+ SwitchA needs to be the root switch for vlans 11, 12, 13, 21, 22 and 23. All other vlans
should be left are their default values.
Configuration Requirements for SwitchB
+ Vlan 21
++ Name: Marketing
++ will support two servers attached to fa0/9 and fa0/10
+Vlan 22
++Name: Sales
++will support two servers attached to fa0/13 and fa0/14
+Vlan 23
++ Name: Engineering
++ will support two servers attached to fa0/15 and fa0/16
+Access ports that connect to server should transition immediately to forwarding state upon
detecting the connection of a device.
+SwitchB VTP mode needs to be the same as SwitchA.
+SwitchB must operate in the same spanning tree mode as SwitchA
+No routing is to be configured on SwitchB
+Only the SVI vlan 1 is to be configured and it is to use address 192.168.1.11/24
Inter-switch Connectivity Configuration Requirements
+For operational and security reasons trunking should be unconditional and Vlans 1, 21, 22
and 23 should tagged when traversing the trunk link.
+The two trunks between SwitchA and SwitchB need to be configured in a mode that allows
for the maximum use of their bandwidth for all vlans. This mode should be done with a nonproprietary protocol, with SwitchA controlling activation.
+Propagation of unnecessary broadcasts should be limited using manual pruning on this trunk link.

SIMULATION
You have been tasked with configuring multilayer SwitchC, which has a partial configuration
and has been attached to RouterC as shown in the topology diagram.

You need to configure SwitchC so that Hosts H1 arid H2 can successful ping the server S1.
Also SwitchC needs to be able to ping server SI.
Due to administrative restrictions and requirements you should not add/delete vlans or
create trunk links Company policies forbid the use of static or default routing All routes must
be learned via EIGRP 65010 routing protocol.
You do not have access to RouteC, RouterC is correctly configured. No trunking has been
configured on RouterC.
Routed interfaces should use the lowest host on a subnet when possible. The following
subnets are available to implement this solution:
• 172.16.1.0/24
• 192.168.3.32/27
• 192.168.3.64/27
Hosts H1 and H2 are configured with the correct IP address and default gateway.
SwitchC uses Cisco as the enable password.
Routing must only be enabled for the specific subnets shown in the diagram.
Note: Due to administrative restrictions and requirements you should not add or delete
VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use
of static or default routing. All routes must be learning via the EIGRP routing protocol.

HOST 1

HOST 2

Refer to the exhibit.

For the configuration shown, which is the recommended method of providing interVLAN routing?