Your network consists of a single Active Directory domain named litwareinc.com.You have server named
DC1 that runs Windows Server 2003 Service Pack 2 (SP2).DC1 has the DNS server role installed and is the only DNS server for the network.
On DC1, you open the DNS snap-in as shown in the exhibit.(Click the Exhibit button.)
At the command prompt, you run Nslookup www.contoso.com and receive the following error message; "***
Localhost can’t find www.contoso.com: Non-existent domain."
You need to ensure that you can connect to Internet hosts by using fully qualified domain names (FQDNs).
What should you do?
Exhibit:

You have two DNS servers named Server1 and Server2 that run Windows Server 2003 Service Pack 2 (SP2).
Server1 hosts a standard primary zone for contoso.com.
On Server2, you create a secondary zone for contoso.com and specify Server1 as the master server.
On Server2, you attempt to open the contoso.com zone and receive the following error message: "Zone not loaded by DNS Server."
You need to ensure that the zone loads on Server2.
What should you do?

You have a DNS server named Server1 that runs Windows Server 2003 Service Pack 2 (SP2).Server1 is
configured to have an IP address of 10.10.0.10.
You run the NSLookup command on the server and receive the following error message.
You need to ensure that this time-out message does not appear when you run NSLookup.
What should you do?

You are the network administrator for A.Datum Corporation.The company uses the adatum.com namespace for its internal network.
The company network consists of two networks that are connected by a WAN link.The 10.9.9.0 network uses the 9.9.0/24 address.The 10.9.8.0 network uses the 10.9.8.0/24 address.
The relevant portion of the network is shown in the exhibit.(Click the Exhibit button.)
The network contains the DNS servers that are configured as shown in the following table.
In the 10.9.9.0/24 network, a server named Server1 frequently needs to resolve names in the adatum.com namespace and on the Internet.You need to configure the TCP/IP properties of Server1 to use the most efficient server as its preferred DNS server.
The number of hops required to resolve any name must be kept to a minimum.You also need to minimize the amount of network traffic that is caused by name resolution.
On Server1, which DNS server should you configure as the preferred DNS server?

Your network contains a head office and one branch office.All servers run Windows Server 2003 Service Pack 2 (SP2).
The network and IP configuration for each server are configured as shown in the exhibit.(Click the Exhibit button.)
Server2 has the Routing and Remote Access service and the DNS Server service installed.Routing Information
Protocol (RIP v2) is enabled on Server2 and all internal routers.
Server1 is unable to connect to the Internet.
You need to ensure that Server1 can connect to the Internet.
What should you do?

Your network consists of a single Active Directory domain named nwtraders.com.All network servers run Windows Server 2003 Service Pack 2 (SP2).
The relevant IP configuration for the network is configured as shown in the following table.
DC1 contains an Active Directory-integrated zone for nwtraders.com.
From Server2, you run the Ping 172.26.26.11 command and receive a request timed out error message.From
Server2, you run the Ping 172.16.16.129 command and receive a reply.
You need to ensure that you can join Server2 to the nwtraders.com domain.
What should you do?

You have two servers named Server1 and Server2 that run Windows Server 2003 Service Pack 2 (SP2).
The IP configuration for Server1 is shown in the Server1 IP exhibit.(Click the Exhibit button.)
The IP configuration for Server2 is shown in the Server2 IP exhibit.(Click the Exhibit button.)
Server1 is unable to contact Server2.
You need to ensure that Server1 can contact Server2.
What should you do?
Exhibit 1 (exhibit):
Exhibit 2 (exhibit):

Your network consists of a single Active Directory domain.You have a server named Server1 that runs
Windows Server 2003 Service Pack 2 (SP2) and Windows Server Update Services (WSUS) 3.0.
From IIS Manager, you configure WSUS to use port 4430 for SSL.You update your WSUS clients to connect to https://Server1:4430 for updates.
You need to ensure that clients can download updates from Server1.
What should you do?

You have a server that runs Windows Server 2003 Service Pack 2 (SP2).The server is configured as a router and provides access to the Internet.
You need to log all connections made to the server.The log must contain the IP address and the port used to establish the connection.
What should you do?