What should you do to prevent unauthorized DHCP clients from receiving addresses from Server1?
Your network contains an Active Directory domain. The domain contains a DHCP server named Server1.
You create a scope named Scope1 on Server1.
You need to prevent unauthorized DHCP clients from receiving addresses from Server1.
exhibit What should you do?
What should you do to ensure that the DHCP server can respond to DHCP clients?
Your network contains a DHCP server that is configured as shown in the exhibit. (Click the Exhibit button.)
You need to ensure that the DHCP server can respond to DHCP clients.
exhibit What should you do?
Exhibit:
What should you do from the DHCP console?
Your network contains two DHCP servers named Server1 and Server2.
On Server1, you create a scope named Scope1.
You need to ensure that DHCP clients receive IP addresses from the address range in Scope1 if Server1 is unavailable. The solution must prevent both servers from assigning duplicate IP addresses.
exhibit What should you do from the DHCP console?
Which address should you assign?
Your network contains a single Active Directory domain. All servers run Windows Server 2008 R2. You have an IPv6-only infrastructure that has multiple subnets. You deploy a new server named Server1.
You need to ensure that Server1 can communicate with the client computers in all of the internal subnets. The solution must use an address that is reserved for internal networks.
exhibit Which address should you assign?
What should you do to display mnemonic host names instead of IP addresses for all the frames?
You perform a security audit on a server named Server1. You install the Microsoft Network Monitor 3.0 application on Server1.
You find that only some of the captured frames display host mnemonic names in the Source column and the Destination column. All other frames display IP addresses. You need to display mnemonic host names instead of IP addresses for all the frames.
exhibit What should you do?
Which filter should you use to build a filter in the Network Monitor application to capture the DHCP traffic b
Your company has a server named DC1 that runs Windows Server 2008 R2. Server1 has the DHCP Server server role installed.
You find that a desktop computer named Computer1 is unable to obtain an IP configuration from the DHCP server.
You install the Microsoft Network Monitor 3.0 application on Server1. You enable P-Mode (Promiscuous Mode) in the Network Monitor application configuration. You plan to capture only the DHCP server-related traffic between Server1 and Computer1.
The network interface configuration for the two computers is shown in the following table.
You need to build a filter in the Network Monitor application to capture the DHCP traffic between Server1 and Computer1.
exhibit Which filter should you use?
What should you do to reduce the number of events registered in the system log on Printer1?
Your company has a server named Printer1 that runs Windows Server 2008 R2. Printer1 has the Print and Document Services server role installed.
You need to reduce the number of events registered in the system log on Printer1.
exhibit What should you do?
What should you do from the Disk Management snap-in to add Disk4 to the RAID-5 volume for drive C?
Your network contains a server named Server1 that runs Windows Server 2003 Service Pack 2 (SP2). Server1 is configured as shown in the following table.
Disk1 fails. You remove Disk1 from the computer and install Disk4.
You open the Disk Management snap-in and discover that the status of Disk1 is Missing. You bring Disk4 online as a dynamic disk. Disk4 has no volume on it.
You need to add Disk4 to the RAID-5 volume for drive C.
What should you do from the Disk Management snap-in?
What should you do to improve the performance of Server1?
Your network contains an application server named Server1 that runs Windows Server 2003 Service Pack (SP2).
You open the Performance tab in Task Manager as shown in the exhibit. (Click the Exhibit button.)
You need to improve the performance of Server1.
What should you do?
Exhibit:
What should you do to restore name resolution in the branch office?
Your company has a main office and a branch office. The company network has two WINS servers. You have an application that requires NetBIOS name resolution. The WINS servers are configured as shown in the following table.
You discover that the WINS addresses on all client computers in both offices are configured in the following order of use:
10.1.0.23
10.6.0.254
You reconfigure the WINS addresses on all client computers in the branch office in the following order of use:
10.6.0.254
10.1.0.23
After the reconfiguration, users in the branch office are unable to connect to the servers that are located in the main office.
You need to restore name resolution in the branch office.
exhibit What should you do?