— Exhibit –user@router# run show interfaces terse
Interface Admin Link Proto Local
fe-0/0/0 up up
fe-0/0/0.0 up up inet 10.0.39.2/24
iso
mpls
fe-0/0/1 up up
fe-0/0/1.0 up up inet 10.0.18.2/24
fe-0/0/1.513 down up inet 10.0.19.2/24
— Exhibit –An administrator is unable to ping any address on the 10.0.19.0/24 subnet. To identify the
problem, the administrator uses the command shown in the exhibit.

Which step should be taken to solve the problem?

— Exhibit –user@router# run show route 10.20.133.0/24
inet.0: 142 destinations, 142 routes (141 active, 0 holddown, 1 hidden)
+ = Active Route, – = Last Active, * = Both
10.20.133.0/24 *[OSPF/10] 04:10:20
> to 172.25.213.11 via ge-1/0/1.0
to 172.25.213.23 via ge-1/0/2.0
— Exhibit –In the exhibit, what does the (>) symbol indicate?

— Exhibit —

user@router> show route protocol static
inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden)
+ = Active Route, – = Last Active, * = Both
192.168.1.0/24 *[Static/5] 00:03:13
> to 10.20.106.10 via fe-0/0/5.106
192.168.1.192/26 *[Static/5] 00:03:13
> to 10.20.14.131 via ge-0/0/0.0
192.168.1.192/27 *[Static/5] 00:03:13
> to 10.18.1.1 via ge-0/0/1.0
192.168.1.4/30 *[Static/5] 00:01:06
> to 10.20.14.130 via ge-0/0/0.0
— Exhibit –Using the routing table shown in the exhibit, what will be the next-hop IP address used for a
destination IP address of 192.168.1.1? (Assume that the only routes to this destination are static
routes.)

— Exhibit –user@router> show route protocol static
inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden)
+ = Active Route, – = Last Active, * = Both

192.168.1.128/27 *[Static/5] 00:03:13
> to 10.20.106.10 via fe-0/0/5.106
192.168.1.144/29 *[Static/5] 00:03:13
> to 10.20.14.131 via ge-0/0/0.0
192.168.1.192/27 *[Static/5] 00:03:13
> to 10.18.1.1 via ge-0/0/1.0
192.168.1.128/28 *[Static/5] 00:01:06
> to 10.20.14.130 via ge-0/0/0.0
— Exhibit –Given the routing entries shown in the exhibit, which next-hop IP address will be used for the
destination IP address 192.168.1.159? (Assume that only static routes are available for the
destination.)

Which CLI mode allows you to make configuration changes?

Which command do you use to navigate to [edit interfaces]?

Which command will display the contents of the forwarding table?

Which operating system do Juniper Networks MX Series routers use?

Which command do you use to go from the shell prompt to the CLI prompt?

Which command will allow you to quickly determine the administrative status of all interfaces on a
Junos device?