2 Comments on “Which three risks should the security director be conce…”

1. Nicholas says:

   August 3, 2017 at 9:46 pm

   2017/Aug New Updated 300-360 exam questions:
   QUESTION 1
   A downstream packet that contains a DSCP value arrives at the WLC Ethernet interface from the
   wired source network. The WLC is configured for QoS WLAN 802.1p mapping.
   How does the WLC treat the CAPWAP QoS marking when leaving the controller interface for the
   respective AP and final wireless client destination?
   A. No outer CAPWAP or inner QoS tagging is applied.
   B. The outer CAPWAP CoS is marked and capped and the inner DSCP maintains the original
   marking.
   C. No outer CAPWAP QoS tag is applied, but the original DSCP is maintained inside CAPWAP.
   D. The outer CAPWAP DHCP is marked and capped without any inner DSCP value.
   Answer: B

   QUESTION 2
   A network engineer wants the DSCP marking to align with the 802.11e access category video.
   What will this marking be?
   A. 34
   B. AF31
   C. 4
   D. 5
   Answer: A

   QUESTION 3
   An engineer receives a digital image scanned from the floor plans of a facility to be surveyed for
   wireless survey and imported it into Air Magnet Pro. However, the document contains no scale.
   Which action can the engineer take to most accurately calibrate the size of the floor plan in Air
   Magnet?
   A. Mark the length of a hallway, then count the ceiling tiles, multiply that number by 2 and enter that
   value.
   B. Zoom in and mark across a hallway, then count the floor tiles across that hallway and enter that
   value.
   C. Zoom in and mark a doorway, then size it at 3 feet because most doorways are 36 inches.
   D. Mark the entire longest dimension of the floorplan, then use Google Earth to measure the
   correspondingoutside dimension and enter that value.
   Answer: D

   QUESTION 4
   While performing a Layer 1 passive wireless site survey of a location an engineer detects several
   instances of low power frequency hopping interference, but cannot physically locate the
   interfering device or devices. Why is the engineer unable to locate the offending device or
   devices?
   A. The sources are nearby narrow-beam radar and are sweeping through the facility.
   B. The sources are PAN and are mobile.
   C. The sources are above the ceiling file and transmit intermittently.
   D. The sources are actually high-powered devices and transmit from off the site.
   Answer: B

   QUESTION 5
   An engineer is assigned to assist a customer by estimating the number of access points needed
   to provide voice-grade wireless coverage in a carpeted office space. How many access points
   should be estimated to cover this space of roughly 38,000 square feet?
   A. 17
   B. 10
   C. 6
   D. 13
   Answer: D

   QUESTION 6
   Which two types of information must be included in the installation inventory portion of the postinstallation
   report? (Choose two.)
   A. all AP, controller, and MSE administrator credentials
   B. the names, locations, IP addresses, MAC addresses, etc. for every AP, controller, and MSE in the
   WLAN
   C. a layout of the rack that the equipment is installed
   D. results of the coverage audit performed with the site survey mapping tool
   E. the number and type of all WLAN clients and tags
   Answer: AB

   QUESTION 7
   An engineer is configuring an autonomous AP for RADIUS authentication. What three pieces of
   information must be known to configure the AP? (Choose three.)
   A. BVI IP address
   B. group name
   C. RADIUS IP address
   D. PAC encryption key
   E. username and password
   F. shared secret
   Answer: BCF

   more new 300-360 exam questions:https://www.braindump2go.com/300-360.html

   
   
   
   0

   
   
   
   0
2. Antonio says:

   September 26, 2017 at 4:37 am

   for me correct answer is ADE

   
   
   
   1

   
   
   
   0