PrepAway - Latest Free Exam Questions & Answers

Which pseudo wire (PW) connections must the administrator configure?

Refer to the exhibit An MPLS VPLS solution (non-hierarchical) will connect the sites shown
in the exhibit Which pseudo wire (PW) connections must the administrator configure?

PrepAway - Latest Free Exam Questions & Answers

A.
A hub-and-spoke set of PWs between one P router and all PE routers that connect to a
site

B.
A full mesh of PWs between every PE router that connects to a site

C.
A hub-and-spoke set of PWs between one PE router and other PE routers that connect
to a site

D.
A full mesh of PWs between every PE router that connects to a site and every P router
between them

115 Comments on “Which pseudo wire (PW) connections must the administrator configure?”

  5. Max says:

    Hello…
    Thanks for the post..
    all answer are wrong!!!.
    There are 15 new questions, anyone has any updated dump?

    Thanks in advance,
    if I find the correct answers will share them as soon as possible.

    regards




    0



    0
  8. ipman says:

    hello guys,
    this exam is very hard.
    there is 17 more questions .
    i will send them to admin.

    many questions are about delivery and answers are in configuration guide available on google.

    Help wanted 😉




    0



    0
  10. Scott says:

    Hello again:

    Look, I have 13 new questions and I going to share with you, but I don’t have the answers, sorry.

    1. Refer to the exhibit

    All switches have established the EVI links shown in the exhibit. Each switch extends VLAN 10 on this EVI network.
    How is the MAC forwarding table for VLAN 10 switch 1 populated with MAC addresses in DC 2 and DC 3?

    A. EVI switches advertise their local VLAN 10 MAC addresses using IS-IS Switch 1 binds a remote MAC address to the EVI link that receives the IS-IS message.

    B. Each EVI switch registers its local VLAN 10 MAC addresses with HP intelligen Management Center (IMC), IMC distribures the correct forwarding table entries to Switch 1.

    C. When Switch 1 receives tunneled traffic on an EVI link, it inspects the source MAC address for the inner frame. It learns the EVI link as the forwarding interface for that address.

    D. After configuring an EVI tunnel on Switch 1 to a peer, the administrator configures the remote Mac addresses connected through that peer.

    —

    2. Refer to the exhibit

    A data center that uses SPBM needs a Layer 3 solution to route traffic for the server subnets. How can administrators configure a core switch to accomplish this?

    A. Set up two VPN instances. The first VPN instance runs SPBM and has a default route through the second VPN instance. The second instance owns VLAN interfaces 10,20, and 30.

    B. Configure IP addresses on VLAN interfaces 10, 20, and 30. Set up TRILL to convert the switch to an RBridge and add the routing functionality.

    C. Set up two MDCs. The first MDC runs SPBM and has a port with SPBM service instance for VLAN 10, 20, and 30. This port connects to a port on the second MDC which routes for the VLANs.

    D. Configure IP addresses on VLAN interfaces 10, 20, and 30 implement routing between the interfaces.

    —

    3. A multi-tenant data center has HP Comware switches configured with several VPN instances. The switches must use Open Shortest Path First (OSPF) to communicate routing information in each instance.
    Which rule must the administrator follow when setting up OSPF?

    A. Create a different OSPF process for each VPN instance.

    B. Use the same OSPF process for all VPN instances but a different OSPF area for each instance.

    C Create a different OSPF process for each VPN instance, and use different area IDs in each process.

    D. Use the same OSPF process and the same OSPF area for all VPN instance.

    —

    4. Which switch series is designed for the HP FlexFabric core and supports TRILL and In-Service Software Upgrade (ISSU)?

    A. HP 9500

    B. HP 12900

    C. HP 12500

    D. HP 5900v

    —

    5. Several HP switches form an SPBM region. The administrator wants the SPBM switches to process IS-IS Link State Packets (LSPs) more quickly and simultaneously. What should the administrator do on each SPBM switch?

    A. Enable Graceful Restar for IS-IS.

    B. Set the IS-IS dead timer for IS-IS to twice the lengh of the IS-IS hello timer.

    C. Create I-SID 255 and reserve that I-SID without placing customer interfaces in it.

    D. Extend a new VLAN across the network and enable IS-IS on that VLAN.

    —

    6. Which requirement must a data center network meet to support federated applications?

    A. Use a hierarchical design that divides the access layer from the core with a distribution layer.

    B. Provide insight into communications that occur entirely whitin a virtualized host.

    C. Support distributed rounting functions to ensure resiliency in all scenarios.

    D. Support a high volume of low latency communications between servers.

    —

    7. Refer to the exhibit

    An administrator is configuring PE-1 to be part of the MPLS domain. The domain uses LDP. On witch interfaces should the administrator enable MPLS and LDP?

    A. Enable MPLS on Ten2/0/1 and Ten2/0/2. Enable LDP on Ten2/0/1 and Ten2/0/2.

    B. Enable MPLS on G1/0/1. Ten2/0/1, and Ten2/0/2. Enable LDP on Ten2/0/1 and Ten2/0/2.

    C. Enable MPLS on G1/0/1. Ten2/0/1, and Ten2/0/2. Enable LDP on G1/0/1, Ten2/0/1 and Ten2/0/2.

    D. Enable MPLS on G1/0/1. Enable LDP on G1/0/1, Ten2/0/1 and Ten2/0/2

    —

    8. An administrator is configuring several HP Comware sw to supports FCoE in Fibre Channel Forwarder (FCF) mode. The switches should be part of the same VSAN or fabric. What is the correct method for setting the VSAN domain ID on the switches?

    A. Set it manually on one switch. Other switches must receive the same ID dynamically from the first switch.

    B. Set it manually to the same value on each switch.

    C. Set it manually as a unique value on each switch.

    D. Do not set it manually as it must match the VSAN ID.

    —

    9. Refer to the exhibit

    PE-1 is being configured as part of a VPLS Martini solution that connects Sites 1,2, and 3. The administrator entered the commands shown in Exhibit. Devices in Site 1
    cannot reach other sites.

    What corrects the misconfiguration?

    A. In the G1/0/1 service instance, set the cross-connect access mode to EThernet mode.

    B. In the VSI, change the PW ID for 10.255.3.3 to a different value from 1010.

    C. In the G1/0/1 service instance, delete the cross-connect binding. Configure a global cross-connect group instead-

    D. In the VSI, add a peer command for P-4 and for P-5.

    —

    10. Refer to the exhibit

    An administrator is setting up an MPLS Layer 2 VPN between customer Sites 1 and 2 and is defining the pseudo wire (PW) ID for this purpose.
    How should the PW IDs and router values be configured?

    A. Set the PW ID to the same value on PE-1 and PE-2. Use a different value from other PWs on these routers.

    B. Set the PW ID to a different value on PE-1 and PE-2. The value on each router must match the label advertised by the peer for its loopback address.

    C. Set the PW ID to the same value on PE-1 and PE-2. The value on each router must match the S-VLAN ID for the associated service instance.

    D. Set the PW ID to a different value on PE-1 and PE-2. Also use a different value from other PWs on these routers.

    —

    11. Refer to the exhibit

    An administrator is setting up an MPLS Layer 2 VPN virtual circuit (VC) between customer Site 1 and 2. On PE-1 a pseudo wire (PW) was set up to PE-2 using
    a cross-connect group. What should the administrator consider when setting up a PW on PE-2 for traffic in the other direction?

    A. Create a PW on PE-2 if the PE-1 PW uses static labels. No configuration is required on PE-2 if the solution is using LDP to communicate labels.

    B. Create a PW pn PE-2 regardless of how the PW is configured on PE-1.

    C. Create a PW on PE-2 if the service instance for the PE-1 PW uses VLAN encapsulation. No configuration is required on PE-2 in other cases.

    D. No configuration is required on PE-2, regardless of how the PW is configured on PE-1.

    —

    12. An HP Comware switch connects to server Converged Network Adaptors (CNAs) on several interfaces. FCoE is set up on the switch for these connections.
    What must the administrator implement on these switch interfaces to ensure lossless delivery for the FCoE traffic?

    A. flow control and strict priority queuing.

    B. DCB eXchange (DCBX), Priority Flow Control (PFC), and Enhanced Transmission Selection (ETS)

    C. Ethernet Virtual Bridging (EVB) in Virtual EThernet Port Aggregator (VEPA) mode

    D. Bi-Directional Forwarding Detection (BFD) and strict priority queuing.

    —

    13. An administrator is configuring HP Comware Switch 1 to support FCoE for connected servers with Converge Network Adaptors (CNAs). On Ten1/0/1, Switch 1
    sends FCoE traffic to an upstream switch also supports FCoE and connects to storage. What is the correct configuration for Switch1 Ten1/0/1?

    A. Bound to a VFC interface, which is in F mode.

    B. FC port in NP mode.

    C. FC port in F mode.

    D. bound to a VFC interface, which is in E mode.

    Anybody knows the answer?

    Thanks in advance




    0



    0
      1. Scott says:

        Hi Wolfking:

        I have to take this exam next week, too

        I am looking for the corrects answers. I took this exam and failed.

        I have a doc with the questions, but not include the answers.




        0



        0
  13. ipman says:

    Hi Guys,

    i pass this exam twice and failed . my best score is 58%
    i work this exam with the book but i don’t have all answers.
    i will write “sure” answers on questions.
    i hope someone here could help us.

    good luck




    0



    0
    1. Scott says:

      Hi..

      So bad, this exam is very hard.
      I’m very worried…
      I took this exam and failed, my score was 25%.
      I guess many people are waiting for the correct answers.
      I have studied with the questions and the study book.
      We hope someone could help us…
      🙁




      0



      0
  15. ipman says:

    Hi Guys,

    i put here some answers about the news questions posted by Scott

    These Answers are only mine. For sure HELP WANTED

    it’s missing 4 new questions.
    i will post them ASAP

    ——————————————————-

    1. Refer to the exhibit

    All switches have established the EVI links shown in the exhibit. Each switch extends VLAN 10 on this EVI network.
    How is the MAC forwarding table for VLAN 10 switch 1 populated with MAC addresses in DC 2 and DC 3?

    i think answer A :
    EVI switches advertise their local VLAN 10 MAC addresses using IS-IS Switch 1 binds a remote MAC address to the EVI link that receives the IS-IS message.

    ———————————————————————

    2. Refer to the exhibit

    A data center that uses SPBM needs a Layer 3 solution to route traffic for the server subnets. How can administrators configure a core switch to accomplish this?

    i think answer C
    C. Set up two MDCs. The first MDC runs SPBM and has a port with SPBM service instance for VLAN 10, 20, and 30. This port connects to a port on the second MDC which routes for the VLANs.

    ——————————————————————

    3. A multi-tenant data center has HP Comware switches configured with several VPN instances. The switches must use Open Shortest Path First (OSPF) to communicate routing information in each instance.
    Which rule must the administrator follow when setting up OSPF?

    I think answer C
    C :Create a different OSPF process for each VPN instance, and use different area IDs in each process.

    ——————————————————————

    4. Which switch series is designed for the HP FlexFabric core and supports TRILL and In-Service Software Upgrade (ISSU)?

    sure answer B
    B. HP 12900
    quickspecs :https://www.hpe.com/h20195/v2/GetPDF.aspx/c04111378.pdf

    —————————————————————————-

    5. Several HP switches form an SPBM region. The administrator wants the SPBM switches to process IS-IS Link State Packets (LSPs) more quickly and simultaneously. What should the administrator do on each SPBM switch?

    i think answer C
    C. Create I-SID 255 and reserve that I-SID without placing customer interfaces in it

    6. Which requirement must a data center network meet to support federated applications?

    i think answer D
    D. Support a high volume of low latency communications between servers.

    —————————————————————————-

    7. Refer to the exhibit

    An administrator is configuring PE-1 to be part of the MPLS domain. The domain uses LDP. On witch interfaces should the administrator enable MPLS and LDP?

    i think answer D
    D. Enable MPLS on G1/0/1. Enable LDP on G1/0/1, Ten2/0/1 and Ten2/0/2

    —————————————————————————–

    8. An administrator is configuring several HP Comware sw to supports FCoE in Fibre Channel Forwarder (FCF) mode. The switches should be part of the same VSAN or fabric. What is the correct method for setting the VSAN domain ID on the switches?

    i think C
    C. Set it manually as a unique value on each switch.

    ———————————————————————————

    9. Refer to the exhibit

    PE-1 is being configured as part of a VPLS Martini solution that connects Sites 1,2, and 3. The administrator entered the commands shown in Exhibit. Devices in Site 1
    cannot reach other sites.

    What corrects the misconfiguration?

    i think answer A
    A. In the G1/0/1 service instance, set the cross-connect access mode to EThernet mode.

    ————————————————————————–

    10. Refer to the exhibit

    An administrator is setting up an MPLS Layer 2 VPN between customer Sites 1 and 2 and is defining the pseudo wire (PW) ID for this purpose.
    How should the PW IDs and router values be configured?

    i think answer A
    A. Set the PW ID to the same value on PE-1 and PE-2. Use a different value from other PWs on these routers.

    ———————————————————————————

    11. Refer to the exhibit
    An administrator is setting up an MPLS Layer 2 VPN virtual circuit (VC) between customer Site 1 and 2. On PE-1 a pseudo wire (PW) was set up to PE-2 using
    a cross-connect group. What should the administrator consider when setting up a PW on PE-2 for traffic in the other direction?

    i think Answer C
    C. Create a PW on PE-2 if the service instance for the PE-1 PW uses VLAN encapsulation. No configuration is required on PE-2 in other cases.

    ———————————————————————————–

    12. An HP Comware switch connects to server Converged Network Adaptors (CNAs) on several interfaces. FCoE is set up on the switch for these connections.
    What must the administrator implement on these switch interfaces to ensure lossless delivery for the FCoE traffic?

    i think answer C
    C. Ethernet Virtual Bridging (EVB) in Virtual EThernet Port Aggregator (VEPA) mode

    ————————————————————————————–

    13. An administrator is configuring HP Comware Switch 1 to support FCoE for connected servers with Converge Network Adaptors (CNAs). On Ten1/0/1, Switch 1
    sends FCoE traffic to an upstream switch also supports FCoE and connects to storage. What is the correct configuration for Switch1 Ten1/0/1?

    i think answer B
    B. FC port in NP mode.

    —————————————————————————-

    Thanks for Helping




    0



    0
    1. Scott says:

      Hello to all:

      I also have some answers

      3.A multi-tenant data center has HP Comware switches configured with several VPN instances. The switches must use Open Shortest Path First (OSPF) to communicate routing information in each instance.

      C Create a different OSPF process for each VPN instance, and use different area IDs in each process.

      Answer C, SURE

      —

      4. Which switch series is designed for the HP FlexFabric core and supports TRILL and In-Service Software Upgrade (ISSU)?

      Answer: B. HP 12900, SURE

      Explanation:

      HPE FlexFabric 12900 Switch Series supports both TRILL & In-Service Software Upgrade (ISSU)

      Both the 9500 and 5900v switches doesn’t support these features.

      HPE FlexFabric 12500 Switch Series supports In-Service Software Upgrade (ISSU).

      12500 Switch doesn’t support TRILL.

      —

      5. Several HP switches form an SPBM region. The administrator wants the SPBM switches to process IS-IS Link State Packets (LSPs) more quickly and simultaneously.
      What should the administrator do on each SPBM switch?

      A. Enable Graceful Restar for IS-IS.

      Answer: A?
      Anyone can confirm

      —

      6. Which requirement must a data center network meet to support federated applications?

      A. Use a hierarchical design that divides the access layer from the core with a distribution layer.

      Answer: I think A,

      Anyone can confirm

      —

      7. An administrator is configuring PE-1 to be part of the MPLS domain. The domain uses LDP. On witch interfaces should the administrator enable MPLS and LDP?

      A. Enable MPLS on Ten2/0/1 and Ten2/0/2. Enable LDP on Ten2/0/1 and Ten2/0/2.

      Answer: I think A.
      Anyone can confirm




      0



      0
  17. ipman says:

    Hi Guys,

    down here the missing questions.

    HELP needed as usual

    ————————————————————————–

    1.an administrator wants to use application TVLs to communicate priority information to a converged network adapter (CNA) connected to interface Ten1/0/1.the administrator has configured a QoS policy for this purpose.
    What are correct ways to apply this policy ? ( select two)

    A.as an outbound QoS policy on interface Ten1/0/1

    B.as an outbound global QoS policy

    C.as an inbound QoS policy on interface Ten1/0/1

    D.as an inbound global QoS policy

    E.as an inbound QoS policy on the VLAN associated with storage traffic

    ——————————————————————-

    2.A label switching router (LSR) knows open shortest path first (OSPF ) routes in the 10.0.0.0/15 range.an administrator wants the LSR to advertise network in the 10.1.0.0/16 range with LDP,However ,the LSR should not advertise in the 10.0.0.0/16 range.
    How can this goal be accomplished?

    A.use independent mode for the label distribution control mode

    B.use static routing for the 10.0_00/16 networks because OSPF routes are always advertised With LDP

    C.Disable automatic LDP mode end use static LDP mode instead

    D.Create an IP prefix listfor the 10.1.0.0/16 networks end specify that prefix list in the LDP trigger policy

    ——————————————————————

    3.refer to exhibit

    The switches in the exhibit form TRILL region_ How can the administrator encourage the switches to load-balance broadcasts, multicasts, and unknown unicasts
    over multiple switch-to-switch links?

    A.Specify the calculation of two trees on the switch With the highest TRILL root priority

    B.Enable TRILL Equal Cost Multipath ( ECMP) on each switch

    C.Enable TRILL ECMP on the switch With the highest TRILL root prionty

    D.Configure backbone links to support at least two VLANs on each switch

    —————————————————————————-

    4.a TRILL solution is being set up on the switch shown in exhibit 1.exhibit 2 shows configurations command entered on the switch 1.The TRILL solution is not forwarding traffic correctly.
    What does the administrator need to fix?

    A.Interfaces Forty1/0/49-1/O/50 must be configured as trunk ports that permit VLANs 10, 20
    and 30

    B.Interfaces Ten1/0/1-1/0/48 must be bound to service instances, and TRILL must be disabled on these interfaces

    C.Interfaces Forty1/0/49-1/O/50 must be configured as TRILL trunk port

    D.Interfaces Ten1/0/1-1/0/48 must be configured as TRILL trunk port

    —————————————————————-

    That’s all folks

    😉




    0



    0
  18. Scott says:

    Hi…
    I can confirm some answer again…

    5. Several HP switches form an SPBM region. The administrator wants the SPBM switches to process IS-IS Link State Packets (LSPs) more quickly and simultaneously. What should the administrator do on each SPBM switch?

    A. Enable Graceful Restar for IS-IS.

    B. Set the IS-IS dead timer for IS-IS to twice the lengh of the IS-IS hello timer.

    C. Create I-SID 255 and reserve that I-SID without placing customer interfaces in it.

    D. Extend a new VLAN across the network and enable IS-IS on that VLAN.

    Answer: D, SURE

    —————————————–

    6. Which requirement must a data center network meet to support federated applications?

    A. Use a hierarchical design that divides the access layer from the core with a distribution layer.

    B. Provide insight into communications that occur entirely whitin a virtualized host.

    C. Support distributed rounting functions to ensure resiliency in all scenarios.

    D. Support a high volume of low latency communications between servers.

    Answer: D, SURE

    We are making an effort to resolve all question, if anyone can participate?

    Thanks




    0



    0
  19. wolfking says:

    Hi Guys
    What about the other Questions i mean the old in the web site
    we don’t have the right answers for all questins here
    scott my dear can you send me a new file with all the question and answers please
    help me i need to pass this exam
    my email wolfking78@gmail.com
    thanks and have a nice day




    0



    0
  24. serafino000 says:

    hello to all,

    i create this pdf from a website.
    http://www.easybytez.com/7gxivanos01b
    with green letters the answers.
    i don’t know if the answers are correct.
    i think the answers are correct because i wrote this exam without help (i have this HP.Passit4sure.HP2-Z34.v2015-03-19.by.Reynaldo.60q.pdf) and i take 17% with 10 correct answers.
    i looking for my answers with this pdf :http://www.easybytez.com/7gxivanos01b and i have 10 corect answers.

    if anyone use this pdf i think to pass exam with score about 77-80%.
    i ‘ll take again the exam at 26-27 September.
    if anyone have the corect answers please send to me to the email:giannoulias.ath@gmail.com

    thank you and good luck.




    0



    0
  28. Scott says:

    Sure, ipman….

    I have 2 new questions…

    A company has a three-tier topology for its large data center and needs to extend Layer 2 connectivity with in the data center. What can be used to provide adequate stability, resiliency, and capacity?

    A. Data Center Bridging (DCB) to collapse the three-tier topology into a more effective single-tier.

    B. EVI or Multicustomer Carrier Ethernet (MCE) to enhance the three-tier topology.

    C. EVI to collapse the three-tier topology into a more effective single-tier.

    D. TRILL or SPBM to enhance the three-tier topology.

    ——————————————————

    An administrator is preparing to assign physical switch interfaces to MDCs on an HP Comware switch. What is an assignment rule?

    A. Multiple MDCs can control the same physical interfaces if the MDCs are assigned different sets of VLANs.

    B. Each MDC has sole control over its interfaces, interfaces are assigned to an MDC on a port group basis.

    C. Multiple MDCs can control the same physical interfaces whitout restrictions.

    D. Each MDC has sole control over its interfaces. Interfaces are assigned to an MDC on a port-by-port basis at administrator discretion.

    I’m looking for the correct answers….
    Anyone can confirm the answers?

    Regards




    0



    0
  29. ipman says:

    Hi Scott

    somes answers

    A company has a three-tier topology for its large data center and needs to extend Layer 2 connectivity with in the data center. What can be used to provide adequate stability, resiliency, and capacity?

    D. TRILL or SPBM to enhance the three-tier topology.

    ————–

    An administrator is preparing to assign physical switch interfaces to MDCs on an HP Comware switch. What is an assignment rule?

    B. Each MDC has sole control over its interfaces, interfaces are assigned to an MDC on a port group basis.

    regards




    0



    0
  31. serafino000 says:

    Hi t all!!

    ipman can you you have take the exam and your score is 65%.
    can you share here all write answers.

    like :

    1)A company has a three-tier topology for its large data center and needs to extend Layer 2 connectivity with in the data center. What can be used to provide adequate stability, resiliency, and capacity?

    D. TRILL or SPBM to enhance the three-tier topology.

    because i see many answers and i confused what is the correct answer.

    everyone you want to send me an email: giannoulias.ath@gmail.com

    thank you all for help.

    regards.




    0



    0
  36. serafino000 says:

    hello to all!
    i need the answers because it must pass the exam before 1st Oct.
    can anyone send me the correct answers in my email: giannoulias.ath@gmail.com

    wolfking do you have any correct answers?
    from here i confused what are the correct answers. i took 2 times the exam and take 17 & 27 %….

    thank you all.




    0



    0
  38. wolfking says:

    HI
    Today i take the exam and fail my score was 62
    i use the IPman and scott answers from the web site
    guys we need to answers correct to the new questions and then we will pass
    any one can help ?
    any one ?
    please i was so close this time
    help please help with the new questions




    0



    0
  39. wolfking says:

    hi
    maybe we need to correct a few answers to the questions in the web site that most of the exam from it and we will pass IPMAN SCOTT GUYS PLEASE HELP
    its urgent HP Will change the exams next months




    0



    0
  41. Scott says:

    Hi ipmam:

    Do you have the answers for these questions?:

    1.an administrator wants to use application TVLs to communicate priority information to a converged network adapter (CNA) connected to interface Ten1/0/1.the administrator has configured a QoS policy for this purpose.
    What are correct ways to apply this policy ? ( select two)

    A.as an outbound QoS policy on interface Ten1/0/1

    B.as an outbound global QoS policy

    C.as an inbound QoS policy on interface Ten1/0/1

    D.as an inbound global QoS policy

    E.as an inbound QoS policy on the VLAN associated with storage traffic

    ——————————————————————-

    2.A label switching router (LSR) knows open shortest path first (OSPF ) routes in the 10.0.0.0/15 range.an administrator wants the LSR to advertise network in the 10.1.0.0/16 range with LDP,However ,the LSR should not advertise in the 10.0.0.0/16 range.
    How can this goal be accomplished?

    A.use independent mode for the label distribution control mode

    B.use static routing for the 10.0_00/16 networks because OSPF routes are always advertised With LDP

    C.Disable automatic LDP mode end use static LDP mode instead

    D.Create an IP prefix listfor the 10.1.0.0/16 networks end specify that prefix list in the LDP trigger policy

    ——————————————————————

    3.refer to exhibit

    The switches in the exhibit form TRILL region_ How can the administrator encourage the switches to load-balance broadcasts, multicasts, and unknown unicasts
    over multiple switch-to-switch links?

    A.Specify the calculation of two trees on the switch With the highest TRILL root priority

    B.Enable TRILL Equal Cost Multipath ( ECMP) on each switch

    C.Enable TRILL ECMP on the switch With the highest TRILL root prionty

    D.Configure backbone links to support at least two VLANs on each switch

    —————————————————————————-

    4.a TRILL solution is being set up on the switch shown in exhibit 1.exhibit 2 shows configurations command entered on the switch 1.The TRILL solution is not forwarding traffic correctly.
    What does the administrator need to fix?

    A.Interfaces Forty1/0/49-1/O/50 must be configured as trunk ports that permit VLANs 10, 20
    and 30

    B.Interfaces Ten1/0/1-1/0/48 must be bound to service instances, and TRILL must be disabled on these interfaces

    C.Interfaces Forty1/0/49-1/O/50 must be configured as TRILL trunk port

    D.Interfaces Ten1/0/1-1/0/48 must be configured as TRILL trunk port

    —————————————————————-

    Thanks a lot again




    0



    0
  45. Scott says:

    Hi serafino00:

    Do you have the answers for theses questions:

    1.an administrator wants to use application TVLs to communicate priority information to a converged network adapter (CNA) connected to interface Ten1/0/1.the administrator has configured a QoS policy for this purpose.
    What are correct ways to apply this policy ? ( select two)

    A.as an outbound QoS policy on interface Ten1/0/1

    B.as an outbound global QoS policy

    C.as an inbound QoS policy on interface Ten1/0/1

    D.as an inbound global QoS policy

    E.as an inbound QoS policy on the VLAN associated with storage traffic

    ——————————————————————-

    2.A label switching router (LSR) knows open shortest path first (OSPF ) routes in the 10.0.0.0/15 range.an administrator wants the LSR to advertise network in the 10.1.0.0/16 range with LDP,However ,the LSR should not advertise in the 10.0.0.0/16 range.
    How can this goal be accomplished?

    A.use independent mode for the label distribution control mode

    B.use static routing for the 10.0_00/16 networks because OSPF routes are always advertised With LDP

    C.Disable automatic LDP mode end use static LDP mode instead

    D.Create an IP prefix listfor the 10.1.0.0/16 networks end specify that prefix list in the LDP trigger policy

    ——————————————————————

    3.refer to exhibit

    The switches in the exhibit form TRILL region_ How can the administrator encourage the switches to load-balance broadcasts, multicasts, and unknown unicasts
    over multiple switch-to-switch links?

    A.Specify the calculation of two trees on the switch With the highest TRILL root priority

    B.Enable TRILL Equal Cost Multipath ( ECMP) on each switch

    C.Enable TRILL ECMP on the switch With the highest TRILL root prionty

    D.Configure backbone links to support at least two VLANs on each switch

    —————————————————————————-

    4.a TRILL solution is being set up on the switch shown in exhibit 1.exhibit 2 shows configurations command entered on the switch 1.The TRILL solution is not forwarding traffic correctly.
    What does the administrator need to fix?

    A.Interfaces Forty1/0/49-1/O/50 must be configured as trunk ports that permit VLANs 10, 20
    and 30

    B.Interfaces Ten1/0/1-1/0/48 must be bound to service instances, and TRILL must be disabled on these interfaces

    C.Interfaces Forty1/0/49-1/O/50 must be configured as TRILL trunk port

    D.Interfaces Ten1/0/1-1/0/48 must be configured as TRILL trunk port

    —————————————————————-

    thanks man




    0



    0
    1. Scott says:

      Hi Serafino:

      I don’t understand what pdf files have the corrects answers… I confused…

      look, for example this question:

      A multi-tenant data center has HP Comware switches configured with several VPN instances. The switches must use Open Shortest Path First (OSPF)to communicate routing information in each instance. Which rule must the administrator follow when setting up OSPF?

      A- Create a different OSPF process for each VPN instance.

      B- Create a different OSPF process for each VPN instance, and use different area IDs in each process.

      C- Use the same OSPF process for all VPN instances but a different OSPF area for each instance.

      D- [Use the same OSPF process and the same OSPF area for all VPN instances.

      On the pdf with 80 questions and answers, says that correct is this A- Create a different OSPF process for each VPN instance.

      But, in your exam was D- Use the same OSPF process and the same OSPF area for all VPN instances.




      0



      0
      1. Eddy says:

        I think ans is A because I do not see anything saying the same OSPF area are used for all VPN instances. I can only see Creating different OSPF process for each VPN instance




        0



        0
  52. serafino000 says:

    hi!

    the first is the answers for the exam. with this take 72%

    the second is the answers when i looking for the correct answers and read about it.

    the second i know has 55-60 correct answers from 80.




    0



    0
  60. serafino000 says:

    do you have anyone qwestions for acmp & accp exams.
    if you have anything please share here or send to my mail: giannoulias.ath@gmail.com.
    if anyone want to ask something can you send me an email.
    thank you.

    i have a message to admin. please open a tab for aruba certifications.
    thank you,
    best regards for this forum….




    0



    0
  63. Eddy says:

    an administrator wants to use application TVLs to communicate priority information to a converged network adapter (CNA) connected to interface Ten1/0/1.the administrator has configured a QoS policy for this purpose.
    What are correct ways to apply this policy ? ( select two)

    A.as an outbound QoS policy on interface Ten1/0/1

    B.as an outbound global QoS policy

    C.as an inbound QoS policy on interface Ten1/0/1

    D.as an inbound global QoS policy

    E.as an inbound QoS policy on the VLAN associated with storage traffic

    The answer is A and B

    Confirmed 100% with student guide.




    0



    0
  64. Eddy says:

    Please see below extract from Student Guide:

    The final configuration step is to activate the QoS policy. This can be done at the
    global or interface level. Both must be applied in the outbound direction for DCBX.




    0



    0
  65. Eddy says:

    I have just passed this exam with 92 % . All the questions are seen on this web site. 80 % of the answer are correct from this web site including serafino000’s upload. Unfortunately I only capture half of the questions , if you need my version of answer on any question , let me know.
    Good luck guys.




    0



    0
    1. Eddy says:

      These are my answers to the new questions.

      1. Refer to the exhibit

      All switches have established the EVI links shown in the exhibit. Each switch extends VLAN 10 on this EVI network.
      How is the MAC forwarding table for VLAN 10 switch 1 populated with MAC addresses in DC 2 and DC 3?
      Ans:
      EVI switches advertise their local VLAN 10 MAC addresses using IS-IS Switch 1 binds a remote MAC address to the EVI link that receives the IS-IS message.
      —————————–
      2. Refer to the exhibit

      A data center that uses SPBM needs a Layer 3 solution to route traffic for the server subnets. How can administrators configure a core switch to accomplish this?

      Ans:
      Set up two MDCs. The first MDC runs SPBM and has a port with SPBM service instance for VLAN 10, 20, and 30. This port connects to a port on the second MDC which routes for the VLANs.
      ————————————–
      A multi-tenant data center has HP Comware switches configured with several VPN instances. The switches must use Open Shortest Path First (OSPF) to communicate routing information in each instance.
      Which rule must the administrator follow when setting up OSPF?
      Ans:
      A. Create a different OSPF process for each VPN instance.

      Ans:
      HP 12900
      —————————————————-
      5. Several HP switches form an SPBM region. The administrator wants the SPBM switches to process IS-IS Link State Packets (LSPs) more quickly and simultaneously. What should the administrator do on each SPBM switch?

      Ans:
      Create I-SID 255 and reserve that I-SID without placing customer interfaces in it.
      —————————————————————–
      6. Which requirement must a data center network meet to support federated applications?
      Ans:
      Support a high volume of low latency communications between servers.
      ——————————————————————–
      7. Refer to the exhibit

      An administrator is configuring PE-1 to be part of the MPLS domain. The domain uses LDP. On witch interfaces should the administrator enable MPLS and LDP?
      Ans:
      Enable MPLS on Ten2/0/1 and Ten2/0/2. Enable LDP on Ten2/0/1 and Ten2/0/2
      ————————————————————————-
      An administrator is configuring several HP Comware sw to supports FCoE in Fibre Channel Forwarder (FCF) mode. The switches should be part of the same VSAN or fabric. What is the correct method for setting the VSAN domain ID on the switches
      Ans:
      Set it manually as a unique value on each switch
      ———————————————–
      9. Refer to the exhibit

      PE-1 is being configured as part of a VPLS Martini solution that connects Sites 1,2, and 3. The administrator entered the commands shown in Exhibit. Devices in Site 1
      cannot reach other sites. What corrects the misconfiguration?
      Ans:
      In the G1/0/1 service instance, set the cross-connect access mode to EThernet mode
      ————————————————————
      10. Refer to the exhibit
      An administrator is setting up an MPLS Layer 2 VPN between customer Sites 1 and 2 and is defining the pseudo wire (PW) ID for this purpose. How should the PW IDs and router values be configured?
      Ans:
      Set the PW ID to the same value on PE-1 and PE-2. Use a different value from other PWs on these routers
      ———————————————————————–
      11. Refer to the exhibit

      An administrator is setting up an MPLS Layer 2 VPN virtual circuit (VC) between customer Site 1 and 2. On PE-1 a pseudo wire (PW) was set up to PE-2 using
      a cross-connect group. What should the administrator consider when setting up a PW on PE-2 for traffic in the other direction?
      Ans:
      Create a PW pn PE-2 regardless of how the PW is configured on PE-1
      ————————————————————————–
      12. An HP Comware switch connects to server Converged Network Adaptors (CNAs) on several interfaces. FCoE is set up on the switch for these connections.
      What must the administrator implement on these switch interfaces to ensure lossless delivery for the FCoE traffic?
      Ans:
      DCB eXchange (DCBX), Priority Flow Control (PFC), and Enhanced Transmission Selection (ETS)
      ———————————————————-
      13. An administrator is configuring HP Comware Switch 1 to support FCoE for connected servers with Converge Network Adaptors (CNAs). On Ten1/0/1, Switch 1
      sends FCoE traffic to an upstream switch also supports FCoE and connects to storage. What is the correct configuration for Switch1 Ten1/0/1?
      Ans:
      bound to a VFC interface, which is in E mode
      ——————————————————–
      A label switching router (LSR) knows open shortest path first (OSPF ) routes in the 10.0.0.0/15 range.an administrator wants the LSR to advertise network in the 10.1.0.0/16 range with LDP,However ,the LSR should not advertise in the 10.0.0.0/16 range.
      How can this goal be accomplished?
      Ans:
      Create an IP prefix listfor the 10.1.0.0/16 networks end specify that prefix list in the LDP trigger policy
      ——————————————————–
      an administrator wants to use application TVLs to communicate priority information to a converged network adapter (CNA) connected to interface Ten1/0/1.the administrator has configured a QoS policy for this purpose.
      What are correct ways to apply this policy ? ( select two)
      Ans:
      as an outbound QoS policy on interface Ten1/0/1
      as an outbound global QoS policy
      —————————————————————–
      The switches in the exhibit form TRILL region_ How can the administrator encourage the switches to load-balance broadcasts, multicasts, and unknown unicasts
      over multiple switch-to-switch links?
      Ans:
      Specify the calculation of two trees on the switch With the highest TRILL root priority
      —————————————————————————————-
      a TRILL solution is being set up on the switch shown in exhibit 1.exhibit 2 shows configurations command entered on the switch 1.The TRILL solution is not forwarding traffic correctly. What does the administrator need to fix?
      Ans:
      Interfaces Forty1/0/49-1/O/50 must be configured as trunk ports that permit VLANs 10, 20
      and 30
      ——————————————————————————————-




      0



      0
  81. Pearlk says:

    Please anyone can share the valid answers? I tried today using AT and VCE (ex**collection) failed with 40%
    Here are the questions of my test and the answer I used (score 40%)

    My email pearlkjm@gmail.com

    *Question 1  (1)
    Refer to the exhibit An MPLS VPLS solution (non-hierarchical) will connect the sites shown
    in the exhibit Which pseudo wire (PW) connections must the administrator configure?

    A. A hub-and-spoke set of PWs between one P router and all PE routers that connect to a
    site
    B. A full mesh of PWs between every PE router that connects to a site
    C. A hub-and-spoke set of PWs between one PE router and other PE routers that connect
    to a site
    D. A full mesh of PWs between every PE router that connects to a site and every P router 
between them
    D

    *Question 2  (1)
    An administrator is configuring an HP switch to run SPBM. Which Spanning Tree Protocol
    (STP) configuration is required?
    A. Disable STP.
    B. Ensure that the switch with the lowest IS-IS router ID has the lowest bridge priority.
    C. Set the spanning tree mode to ECT.
    D. Map all B-VLANs to MSTP instance 4092
    C

    *Question 3  (1)
    An administrator creates two VPN instances on an HP Comware switch, in addition to the
    public instance. The switch implements routing protocols and MPLS. Which statement is
    correct about the routing tables and Label Forwarding Information Bases (LFIBs)
    maintained by the switch?
    A. The switch uses a single routing table and maintains a separate LFIB for each VPN
    instance
    B. The switch maintains a separate routing table and LFIB for each VPN instance, but the 
public tables automatically include entries from the other instances.
    C. The switch maintains a separate routing table and LFIB for each VPN instance.
    D. The switch maintains a separate routing table for each VPN instance and uses a single
    LFIB
    B

    *Question 4  (1)
    An HP Comware switch uses the MDC feature and has two MDCs defined Administrators
    want MDC 1 and MDC 2 to be able to exchange traffic. How should the administrators
    complete the configuration?
    A. Connect a physical port that belongs to MDC 1 to a physical port that belongs to MDC 2
    B. Configure MDC 0 to permit data exchange and add a backplane mapping between MDC 
1 and MDC 2.
    C. Create a virtual port on MDC 0 and tag that port for the MDC 1 and MDC 2 management
    VLANs
    D. Create a virtual port with the same name on MDC 1 and MDC 2.
    B

    *Question 5  (1)
    Refer to the exhibit An administrator is setting up an MPLS Layer 2 VPN between customer
    Sites 1 and 2 and is defining the pseudo wire (PW) ID for this purpose. How should the PW
    IDs and router values be configured?
    A. Set the PW ID to a different value on PE-1 and PE-2 Also use a different value from other
    PWs on these routers.
    B. Set the PW ID to the same value on PE-1 and PE-2. Use a different value from other
    PWs on these routers.
    C. Set the PW ID to the same value on PE-1 and PE-2. The value on each router must
    match the S-VLAN ID for the associated service instance.
    D. Set the PW ID to a different value on PE-1 and PE-2 The value on each router must 
match the label advertised by the peer for its loopback address.
    D

    Question 6
    How does a non-hierarchical VPLS Martini solution prevent looping for broadcasts and
    multicasts?
    A. PEs use split horizon operations, never forwarding a packet received on a pseudo wire
    (PW) over another PW.
    B. PEs implement Shortest Path Bridging (SPB) VLAN Mode (SPBV).
    C. PEs use a hub and spoke topology, relying on the hub to distribute broadcasts and
    multicasts.
    D. PEs implement a version of Spanning Tree Protocol (STP). preferably Multiple STP 
(MSTP).
    D

    *Question 7
    A large data center needs to extend its Layer 2 connectivity and isolate tenants who might
    use the same VLAN IDs Which technology accomplishes this goal?
    A. SPBM
    B. Data Center Bridging (DCB)
    C. Multi-VPN-Instance CE (MCE)
    D. TRILL
    C

    Question 8
    To provide redundancy, a company has multiple data centers that use server virilization.
    What is a networking requirement for this scenario?
    A. localized storage volumes that are isolated within each data center
    B. extension of Layer 2 connectivity across the data centers
    C. physical network segmentation and isolation implemented at Layers 1 through 7
    D. less bandwidth at the server access layer and more bandwidth at the distribution layer
    than in a non-virtualized network
    C

    Question 9
    Refer to the exhibit The exhibit displays a company with two data centers that connect by
    using EVl. The company needs a redundant solution for routing traffic between the subnets.
    What is the best way to accomplish this goal?
    A. Place the EVl tunnel interface on each IRF virtual device in a different VPN instance, and
    then set up routing on each device by using the same IP addresses.
    B. Use TRILL on the EVl network.
    C. Combine IRF 1 and IRF 2 into the same IRF virtual device, and set up routing on that 
device
    D. Run Virtual Router Redundancy Protocol (VRRP) on the data center subnets
    C

    *Question 10
    In addition to the Admin MDC, an HP Comware switch supports two MDCs: MDC 2 and
    MDC 3. The administrator wants to allow tenants for both MDCs to log in to CLI for their
    own MDC without first accessing the Admin MDC How can the administrator accomplish
    this goal?
    A. Define a VLAN as the MDC Management VLAN in the Admin MDC. On each MDC.
    create this VLAN. assign a port to it. set up an IP address on it. and set up Telnet or SSH
    access through it.
    B. Create subinterfaces for the AUX user-interface in the Admin MDC. Assign one of the
    subinterfaces to each of the MDCs. and set up Telnet or SSH access through that interface
    C. Assign a console port to each MDC Tenants can then connect their own terminal 
equipment to their assigned port.
    D. Define a physical port as the Management-Ethernet interface in the Admin MDC On each
    MDC. configure a different IP address for this interface, and set up Telnet or SSH access
    through it.
    C

    *Question 11
    What is the purpose of the nickname in TRILL switch settings?
    A. The nickname identifies the TRILL region and must match on every TRILL RBridge in the
    region.
    B. Administrators can use the nicknames to identify switches in CLI output.
    C. The nickname is the first factor for electing a root bridge
    D. TRILL RBridges use the nicknames as source and destination addresses in TRILL
    headers
    C

    *Question 12
    Several VPN instances have been set up on an HP Comware switch. What should the
    administrator do to ensure that no VPN instance uses up too many switch resources?
    A. Bind each instance to a specific port group or ASIC
    B. Set a maximum number of routes that each instance can have in its routing table.
    C. Apply a service policy to each instance to assign that instance a percentage of resources
    D. Set a CPU weight for each VPN instance to control how much of the CPU the instance
    can use.
    A

    *Question 13
    Refer to the exhibit The company wants to use TRILL in the backbone links shown in the
    exhibit. Servers use VLANs 10, 20, and 30 and should be able to communicate across the
    backbone. On which Switch 1 interfaces should the administrator enable TRILL?
    A. VLAN interface 1 only
    B. VLAN interfaces 1,10, 20, and 30
    C. interfaces Forty1/0/49 and Forty1/0/50 only
    D. interfaces Ten1/0/1 to Ten1/0/48, and Forty1/0/49 and Forty1/0/50
    B

    Question 14
    Refer to the exhibit An administrator is setting up MPLS Layer 2 VPN connections between
    several customer sites and wants to send traffic that arrives on G1/0/1 with VLAN tag 102 to
    Site 2. Traffic with a different tag will be sent to a different site How should the administrator
    implement this’?
    A. Set the encapsulation for service-instance 1 to S-VLAN 102
    B. Set the peer PW outer label to 102 in xconnect-group Site1toSite2.
    C. Remove service-instance 1 from interface G1/0/1 and add it to VLAN 102
    D. Set the peer PW inner label to 102 in xconnect-group Site1toSite2.
    C

    Question 15
    Which HP solution is an example of network function virtualization (NFV)?
    A. HP Virtual Services Router (VSR)
    B. HP 12900 Series Switch
    C. HP 5900CP Series Switch
    D. HP IRF virtual device
    A

    *Question 16
    A multi-tenant data center with 12 tenants has the following goals: Isolate tenants to enable
    each tenant to have its own routing space Isolate the data center’s services in its own
    routing space. Allow for some leaking of route information among tenants and company
    services Which feature should be configured on the data center routing switches?
    A. Multi-VPN-Instance CE (MCE)
    B. MDC
    C. VPLS
    D. MPLS
    B

    *Question 17
    An HP Comware Switch 1 supports FCoE for connected servers with Converged Network
    Adapters (CNAs). On interface Ten 1/0/1 Switch 1 sends FCoE traffic in VSAN 2 to an
    upstream switch. Switch 2. which also supports FCoE What is the correct configuration for
    interface Ten 1/071?
    A. FC trunk port, which permits VSAN 2
    B. bound to a VFC interface, which is a trunk port and permits VSAN 2
    C. bound to a VFC interface, which is an access port in VSAN 2
    D. FC access port in VSAN 2
    B

    *Question 18
    An HP Comware switch supports FCoE in Fibre Channel Forwarder (FCF) mode. A switch
    interface Ten1/0/1 connects to a server FCoE Converged Network Adapter (CNA). The
    CNA will carry normal data traffic and storage traffic for VSAN 2. which is associated with
    VLAN 20. How does the administrator assign FCoE traffic for this CNA to VSAN 2?
    A. by accessing the VLAN 20 configuration view and specifying Ten1/0/1 as a member port
    of the VLAN
    B. by setting Ten1/0/1 to FCoE mode and specifying VSAN 2 as the port access VSAN
    C. by accessing the VSAN 2 configuration view and specifying Ten1/0/1 as a member port 
of the VSAN
    D. by binding a VFC interface to Ten 1/0/1 and specifying VSAN 2 as the VFC interface
    trunk VSAN
    C

    *Question 19
    Refer to the exhibit An administrator is setting up this data center topology to use SPBM
    VMs in the same subnet should be able to communicate at Layer 2 and be isolated at Layer
    2 from other subnets. On which Switch 1 interfaces should the administrator enable SPBM?
    A. VLAN interfaces 10, 20, and 30
    B. interfaces Ten1/0/1-Ten1/0/48 and interfaces Forty1/0749-1/0750
    C. interfaces Forty 1/0749-1/075€ only
    D. VLAN interfaces 101 and 103
    B

    *Question 20
    An HP IRF virtual switch with two members is implementing SPBM. The administrator wants
    to ensure that the master can fail without causing topology changes or changes in
    forwarding tables in the SPBM region. Which setting helps support this requirement?
    A. non-stop-forwarding for SPBM
    B. Bidirectional Forwarding Detection (BFD) Multi-Active Detection (MAD) for the IRF link
    C. tandem replication for multicasts
    D. persistent MAC address for IRF
    B

    Question 21
    Refer to the exhibits Exhibit 1 This data center topology is being set up to use SPBM. VMs
    in the same subnet should be able to communicate at Layer 2 and be isolated at Layer 2
    from other subnets. VS110010 was created for VLAN 10 as shown in Exhibit 2. The
    administrator is configuring a service instance for the VLAN 10 traffic on Switch 1 interface
    Ten1/0/1. What is the correct encapsulation mode?
    A. s-vid101
    B. ta99ed
    C. default
    D. s-vid10
    D

    *Question 22
    Refer to the exhibit These switches form an SPBM region. What is required for load
    balancing to occur across the links between these switches?
    A. IS-IS cost for each backbone link must be the same (with IS-IS ECMP enabled).
    B. B-VLANs must be configured to use different ECT algorithms.
    C. Tandem multicast mode must be enabled globally
    D. B-VLANs must be assigned to different MSTP instances.
    B

    Question 23
    To support FCoE traffic, a switch port needs to use Application TLVs to communicate
    application priority information to a Converged Network Adapter (CNA). The setup process
    includes the configuration of an Access Control List (ACL). What is a valid ACL?
    A. Standard ACL that selects traffic by source IP address
    B. Ethernet ACL that selects traffic by Ethertype
    C. Advanced ACL that selects traffic by UDP source port
    D. Advanced ACL that selects traffic by TCP source port
    A

    *Question 24
    Refer to the exhibit • useOSPF • have established an MPLS domain. • use LDP. • have
    established a Martini Layer 2 VPN between Sites 1 and 2 VPN traffic is using the link
    between PE-1 and P-4, and this link fails. What happens to the VPN traffic?
    A. It fails over to the link between PE-1 and P-5 only //administrators created a backup
    virtual circuit (VC) from PE-1 to
    B. It fails over to the link between PE-1 and P-5 only if administrators created two virtual
    circuits (VCs) between PE-1
    C. and PE-2.
    D. It fails over to the link between PE-1 and P-5. The failover is automatically handled by
    MPLS. LDP, and OSPF
    E. It is disrupted for this particular site-to-site connection until the link is fixed
    E

    Question 25
    An HP Comware switch port is being connected to a server Converged Network Adaptor
    (CNA). The CNA and the switch port need to communicate about parameters for various
    priority flow control (PFC) and bandwidth control mechanisms. How does the administrator
    enable these communications?
    A. Enable PFC globally and then enable PFC on the switch port
    B. Enable LLDP globally and then enable Data Center Bridging eXchange (DCBX) TLVs on
    the switch port
    C. Enable the Fibre Channel (FC) fabric port function on the switch port and then set the
    port as an F-port.
    D. Enable Ethernet Virtual Bridging (EVB) on the switch port.
    D

    *Question 26
    Which advantage does a VPLS solution offer over a simple MPLS Layer 2 VPN solution?
    A. extends Layer 2 connectivity across an IP network that uses non-Ethernet media
    B. provides data integrity and privacy for the company traffic
    C. provides MAC learning for VLANs extended across the MPLS region
    D. allows for a hub and spoke pseudo wire (PW) configuration instead of a full mesh
    configuration
    C

    *Question 27
    An administrator binds VLAN interface 10 to VPN instance “TenantA” on an HP Comware
    switch by using this configuration: interface Vlan-interface 10 ip address 10.1.10.1
    255.255.255.0 How does the administrator’s action affect the interface IP address?
    A. The IP address remains 10.1 10.1/24. but now this subnet can also be assigned to an 
interface in another VPN instance.
    B. The interface loses the IP address and the administrator must map the interface to 10.1
    10.1/24 from the VPN instance context
    C. The interface loses the IP address, and the administrator must configure the IP address
    on this interface again.
    D. The IP address remains 10.1.10.1/24 but is extended with the Route Distinguisher (RD)
    and can now be assigned to an interface in another VPN instance.
    A

    Question 28
    Multiple data centers connect over an HP EVI network. IPv4 servers in the data centers use
    Microsoft network load-balancing and need to send multicasts to each other across EVI
    links. They do not use IGMP to join the multicast groups. What must the administrator do?
    A. Configure selective flooding for the multicast group addresses on the EVI tunnel 
interfaces
    B. Enable Protocol Independent Multicasting (PIM) on the EVI tunnel interfaces.
    C. Enable IGMP proxy on the EVI tunnel interfaces.
    D. Enable Multicast Learner Discovery (MLD) on the EVI tunnel interfaces.
    A

    *Question 29
    Refer to the exhibit PE-1 receives an IP packet that is destined to 10 1.10 10 and does not
    have an MPLS header. What does PE-1 do?
    A. drops the packet
    B. adds an MPLS header without a label and forwards the packet to 10.1.1.1 on VLAN 17
    C. adds an MPLS header with label 1150 and forwards the packet to 10.1.1.1 on VLAN 17
    D. forwards the packet to 10.1.1.1 on VLAN 17 without an MPLS header
    B

    *Question 30
    An administrator configures an HP Comware switch to support FCoE in Fibre Channel
    Forwarder (FCF) mode A switch interface connects to a server Converged Network Adapter
    (CNA). which sends normal data and storage traffic What is the correct configuration for this
    port?
    A. FC port in F mode
    B. FC port in NP mode
    C. bound to a VFC interface, which is in F mode
    D. bound to a VFC interface, which is in E mode
    A

    Question 31
    Refer to the exhibit An administrator is planning an MPLS solution and wants to make sure
    that traffic from 10.1.0.0716 to 10.2 0.0/16 takes the best path. The solution is not using
    Traffic Engineering (TE). How does PE-1 choose between the label advertised for
    10.2.0.0/16 by P-4 and by P-5?
    A. based on which peer is the higher priority LDP peer
    B. based on which peer is the next hop in the best route in the IP routing table
    C. based on which link has the lower LDP cost
    D. based on which link has the lower MPLS cost
    B

    *Question 32
    Why might a customer decide to use MDC instead of Multi-VPN-Instance CE (MCE)?
    A. to isolate tenants while maintaining the ability to leak routes in and out of a tenant 
instance
    B. to integrate with Intelligent Resilient Framework (IRF)
    C. to manage all routing and switch functions with a single management team
    D. to provide further segmentation between tenants at the hardware or ASIC level
    A

    *Question 33
    Refer to the exhibit An administrator is configuring an MPLS VPLS Martini solution on PE-1.
    The VPLS solution should connect customer A sites 1, 2, and 3 Where should the
    administrator specify the LDP peers and pseudo wire (PW) label for the PWs?
    A. in service instances on interfaces Ten2/0/1 and Ten2/0/2
    B. in a Virtual Switch Instance (VSI) for customer A
    C. in a service instance on interface G1/0/1
    D. in a global cross-connect group
    C

    *Question 34
    An administrator configures an HP Comware switch to support FCoE in Fibre Channel
    Forwarder (FCF) mode A switch interface connects to a server FC host bus adapter (HBA)
    What is the correct configuration for this port?
    A. bound to a VFC interface, which is in E mode
    B. FC port >n F mode
    C. bound to a VFC interface, which is in F mode
    D. FC port in NP mode
    A

    *Question 35
    What must be used when implementing the backbone multicast feature to isolate multicasts
    in the SPBM region?
    A. maximum of two Equal Cost Tree (ECT) algorithms
    B. single l-SID for all VLANs belonging to the same customer
    C. head-end replication for multicasts
    D. odd-numbered VLAN IDs for B-VLANs
    D

    Question 36
    Refer to the exhibit An EVI network is being set up as shown in Exhibit 1. Part of Switch 1’s
    configuration is shown in Exhibit 2 All other switches are configured correctly and can reach
    each other. The EVI links should carry traffic in VLANs 4 to 20; however, when the
    administrator tries to ping a VLAN 4 device in DC 2 from DC 1. the ping fails. What should
    the administrator do?
    A. Add tunnel destination IP addresses to the tunnel interface.
    B. Either disable the neighbor-discovery server setting or remove the client setting
    C. Change the tunnel source IP address to the Switch 1 router ID.
    D. Configure the tunnel interface to extend VLANs 4 to 20 instead of VLAN 100.
    B

    *Question 37
    Which statement is correct about a Fibre Channel (FC) node-port (N-port) in a Storage Area
    Network (SAN) fabric topology?
    A. It is a port on an initiator or a target, and it connects to a fabric port (F-port)
    B. It is a port on a SAN switch that connects to an initiator or target
    C. It is a port on a SAN switch that connects to a target but never to an initiator
    D. It is a port on an initiator but never a target, and it connects to an extension port (E-port).
    C

    Question 38
    An HP Comware switch supports FCoE in Fibre Channel Forwarder (FCF) mode. A switch
    interface Ten1/0/1 connects to a server FCoE Converged Network Adapter (CNA). The
    CNA transmits normal data traffic, which is tagged for VLANs 4 and 8. and storage traffic for
    VSAN 2, which is associated with VLAN 20. What is a correct port type and VLAN
    configuration for Ten 1/0/1?
    A. a trunk port that has PVID 1 and permits VLANs 4. 8. and 20
    B. a hybrid port that has PVID 1. defines VLAN 20 as untagged, and defines VLANs 4 and 8
    as tagged
    C. a hybrid port that has PVID 1 and defines VLANs 4 and 8 as tagged
    D. a trunk port that has PVID 20 and permits VLANs 4. 8. and 20
    C

    *Question 39
    Refer to the exhibit An administrator is creating the EVI network shown in the exhibit
    Switches 1 and 2 are configured as ENDP servers. and Switch 3 is configured as an ENDP
    client to the ENDP servers. Which configuration is correct for the EVI tunnel interface on
    Switch 3?
    A. The source IP address is the switch router ID; the addresses for switches 1. 2. and 4
    need to be set as destinations
    B. The source IP address is the address on the connection to the service provider; no other
    destination IP addresses need to be set.
    C. The source IP address is the address on the connection to the service provider; the 
addresses for switches 1, 2, and 4 need to be set as destinations
    D. The source IP address is the switch router ID; no other destination IP addresses need to
    be set.
    C

    *Question 40
    An administrator is implementing MDC and wants to create a redundant solution where
    each MDC uses two physical HP Comware switches What is the correct setup process?
    A. Combine the two switches in an Intelligent Resilient Framework (IRF) virtual device Set 
up the MDCs on this device.
    B. Set up the MDCs on both switches. Use the Admin MDC to configure Intelligent Resilient
    Framework (IRF) on the two switches
    C. Set up the MDCs on both switches. Configure Intelligent Resilient Framework (IRF)
    between the two switches on each MDC separately.
    D. Enable MDC on both switches in resiliency mode Configure the MDCs on each device
    using the same MDC IDs on each Connect the devices.
    A

    Question 41
    An HP IRF virtual switch with two members is implementing TRILL. The administrator wants
    to ensure that the master can fail without causing topology changes or changes in
    forwarding tables in the TRILL region. Which setting helps support this requirement?
    A. non-stop-forwarding for TRILL
    B. Graceful Restart for TRILL
    C. Bidirectional Forwarding Detection (BFD) Multi-Active Detection (MAD) for the IRF link
    D. calculation of at least two trees
    A

    Question 42
    Refer to the exhibit An administrator wants these switches to establish a TRILL region
    TRILL is enabled globally and nicknames are set. What must the administrator do so that
    each TRILL switch (RBridge) finds the best path to all other TRILL switches?
    A. Create a Virtual Service Instance (VSI) on each switch and define the other switches as
    TRILL peers.
    B. Configure DRB priorities on all switch-to-switch links.
    C. Configure IS-IS on VLAN 1 on all the switches.
    D. Enable TRILL with the correct link-type on each switch-to-switch port
    C

    Question 43
    Refer to the exhibit An administrator is establishing an MPLS domain to allow
    communication between 10.1.0.0/16.10 2 0 0/16. and 10.3 0.0/16. The solution will use
    OSPF routing and LDP. Onwhich PE and P devices should these protocols be configured?
    A. All P and PE devices should be configured with MPLS, but only P devices need OSPF.
    and only PE devices need LDP.
    B. All P and PE devices should be configured with MPLS, LDP. and OSPF.
    C. All P and PE devices should be configured with MPLS, but only PE devices need OSPF 
and LDP.
    D. All P and PE devices should be configured with MPLS and LDP. but only PE devices
    need OSPF.
    C

    *Question 44
    Which option is correct about the flash memory of an HP Comware switch with multiple
    MDCs?
    A. Each MDC has its own subfolder in the flash, but it can also access another MDC’s
    subfolder if administrators specifically reference the appropriate folder ID.
    B. The entire flash directory is shared by every MDC. All MDCs have root access. 
Administrators may create new subfolders.
    C. Each MDC. including the Admin MDC. can only access its own subfolder in the flash The
    Admin MDC can also access the root folder, but not the subfolder for other MDCs.
    D. Except for the Admin MDC. each MDC can only see and access its own subfolder in the
    flash. The Admin MDC has root access to the root folder and all subfolders.
    B

    *Question 45  (1)
    Refer to the exhibit A company added a second data center IRF 1 and IRF 2 connect on
    direct Ethernet cables. What is the simplest, most flexible and resilient option for the data
    center connection?
    A. EVI network between IRF 1 and IRF 2
    B. IRF 1 and IRF 2 combined into a single IRF virtual device
    C. link aggregation between IRF 1 and IRF 2
    D. VPLS solution between IRF 1 and IRF 2
    C

    *Question 46
    What is an appropriate situation for configuring an interface as a silent TRILL access port?
    A. The interface connects to a downstream non-TRILL switch, which is connected to
    another TRILL switch. The administrator does not want the interface to carry encapsulated
    TRILL traffic.
    B. The interface connects to a downstream non-TRILL switch, which is connected to
    another TRILL switch The administrator wants the interface to provide a backup path for
    encapsulated TRILL traffic
    C. The interface connects directly to server NICs. and it is a bridge aggregation on an IRF 
virtual device.
    D. The interface connects to another TRILL switch, which has a higher DRB priority than
    this switch
    C

    *Question 47
    Which statement is correct about defining a Route Distinguisher (RD) for a VPN instance on
    an HP Comware switch?
    A. The RD is only required when the router runs Border Gateway Protocol (BGP) and must
    be unique to that VPN instance.
    B. The RD is always required and must match the switch global router ID.
    C. The RD is only required when the router runs Border Gateway Protocol (BGP) and must 
match the BGP router ID.
    D. The RD is always required and must be unique to that VPN instance.
    C

    *Question 48
    What is the relationship between a Forwarding Equivalence Class (FEC) and the MPLS
    label that a Label Switching Router (LSR) advertises for that FEC?
    A. An LSR assigns the same label to FECs with the same best next hop: labels remain
    constant across the MPLS domain
    B. The LSR assigns a unique label to each FEC, but labels assigned by different LSRs do
    not necessarily match.
    C. The LSR assigns a unique label to each FEC. and that label remains constant across the 
MPLS domain
    D. An LSR assigns the same label to FECs with the same best next hop; labels assigned by
    different LSRs do not necessarily match
    C

    Question 49
    What is the correct use case for implementing priority flow control (PFC) on a switch port?
    A. The port carries multimedia voice and video traffic PFC should be applied to the queues
    with a lower priority than multimedia traffic
    B. The port carries data and storage traffic PFC should be applied to the queues with a
    lower priority than storage traffic.
    C. The port carries data and storage traffic. PFC should be applied to the priority queue that
    is assigned to storage traffic.
    D. The port carries multimedia voice and video traffic PFC should be applied to the priority 
queue that is assigned to multimedia traffic.
    D

    *Question 50
    A company merger created a situation in which some network segments are using
    overlapping IP addresses. Administrators want to keep the overlapping addresses and
    isolate the segments. A core router connects to devices in both segments and routes some
    traffic for both. What allows this router to route the traffic without conflict?
    A. VPLS
    B. Provider Backbone Bridging (PBB)
    C. Multi-VPN-Instance CE (MCE)
    D. EV1
    B

    *Question 51
    Refer to the exhibit An MPLS Layer 2 VPN is being implemented between Sites 1 and 2.
    The administrator wants PE-1 and PE-2 to set up the Virtual Circuit (VC) dynamically by
    using the Martini method. What is required to accomplish this goal?
    A. remote LDP session between PE-1 and PE-2
    B. iPSec tunnel between PE-1 and PE-2
    C. redistribution of Border Gateway Protocol (BGP) routes into Open Shortest Path First 
(OSPF) on PE-1 and PE-2
    D. VPN instance with the same route distinguisher (RD) on PE-1 and PE-2
    C

    *Question 52
    Refer to the exhibit SPBM is being implemented on the backbone links shown in the exhibit.
    The servers in VLAN 10 (10.1.10.0/24) should be able to communicate at Layer 2 across
    the backbone. In the vsi section of the configuration on Switch 1. which logical components
    are required?
    A. the S-VLAN to which the servers are assigned and the ECT algorithm for distributing their
    traffic
    B. a unique l-SID for the servers and the B-VLAN that should carry their traffic
    C. the S-VLAN to which the servers are assigned and the B-VLAN that should carry their 
traffic
    D. a unique l-SID for the servers and the S-VLAN to which the servers are assigned
    C

    Question 53
    Which statement is correct about a Fibre Channel (FC) World Wide Name (WWN)?
    A. It is a hardware specific address for a LUN on a storage disk and can be used to direct
    FC frames to targets.
    B. It is assigned to an FC N-port as its switch joins the fabric and can be used to route FC
    frames
    C. It is a hardware specific address for an FC device and can be used to place the device in
    zones.
    D. It is assigned to an FC device based on its location and can be used to deliver FC frames
    A

    *Question 54
    Refer to the exhibit An HP Comware switch is configured to support FCoE in Fibre Channel
    Forwarder (FCF) mode Serverl should be able to discover storage targetl and target2. but
    not target3 Assume that the zone-aliases have been configured to reference the FC devices
    correctly Which zone(s) should be added to the active zoneset?
    A. zone 1, zone 2, and zone 3
    B. zone 1 and zone 5
    C. zone 4
    D. zone 6
    B

    *Question 55
    Refer to the exhibit A VSAN is being set up on an HP Comware switch that will connect to
    server Converged Network Adapters (CNAs) and storage systems The administrator is
    checking the configuration of the VSAN with display commands The exhibit shows the
    results. What is a potential issue?
    A. The fabric name has been set to the same ID as the switch WWN. which causes
    conflicts.
    B. The distribute mode for zones has been set to active only, which can cause issues with
    redundancy.
    C. The current zoning configuration does not permit any communication.
    D. The domain ID has been set manually to a preferred ID, but this switch does not have the 
highest priority
    D

    *Question 56
    HP Comware Switch 1 connects to servers with Converged Network Adapters (CNAs) that
    send data and FCoE storage traffic Switch 1 should forward all FCoE traffic to an upstream
    FCoE switch. Switch 2. which will handle all the FLOGI requests, zoning, and FC traffic
    forwarding. What is the correct FCoE mode setting for Switch 1?
    A. NPV
    B. FCF
    C. disabled
    D. hybrid
    A

    *Question 57
    An administrator configures two VSANs on an HP Comware IRF virtual switch. The IRF
    members connect to a server with two Converged Network Adapters (CNAs) One CNA is
    connected to VSAN 1. and the other is connected to VSAN 2 The storage target for the
    server is also connected to VSAN 1 and VSAN 2. What is required for this setup to work?
    A. The HP switch must place the ports connected to the server CNAs in a link aggregation
    set to static mode
    B. The HP switch must support multi-path I/O (MPIO).
    C. The server CNAs must support multi-path I/O (MPIO)
    D. The HP switch must place the ports connected to the server CNAs in a link aggregation 
set to dynamic (LACP) mode
    D

    *Question 58
    When is it recommended to block VRRP hellos between routers in the same VRRP
    instance?
    A. when the VRRP master and VRRP backup router are part of the same IRF virtual device
    B. when providing two VRRP master routers to be deployed in different data centers
    C. when the VRRP master and VRRP backup router are part of a TRILL domain
    D. when the VRRP master and VRRP backup router are top of the rack (ToR) switches
    B

    Question 59
    A customer is deciding whether to purchase a switch in the HP 5900AF Series or the HP
    5900CP series Which need requires the customer to choose the HP 5900CP switch instead
    of the 5900AF switch?
    A. enhanced visibility for VM-to-VM traffic and Ethernet Virtual Bridge (EVB) solutions
    B. OpenFlow support and compatibility with HP software-defined networking (SDN)
    solutions
    C. LAN/SAN convergence support and native FC port connections
    D. support of 10GbE to the server edge and 40GbE uplinks
    A

    *Question 60
    A company is adding a second data center for disaster recovery. The data centers connect
    over a link supplied by a service provider with an IP network. The company wants a solution
    that extends Layer 2 connectivity between the data centers and does not require any
    special services from the service provider, such as MPLS. What can meet the needs for this
    design?
    A. SPBM
    B. QEVI
    C. lRF
    D. VPLS
    A

    *Question 61
    Which switch series is designed for the HP FlexFabric core and supports TRILL and In-Service Software Upgrade (ISSU)?
    B. HP 12900

    *Question 62
    Refer to the exhibit
    PE-1 is being configured as part of a VPLS Martini solution that connects Sites 1,2, and 3. The administrator entered the commands shown in Exhibit. Devices in Site 1
    cannot reach other sites. What corrects the misconfiguration?
    Ans:
    In the G1/0/1 service instance, set the cross-connect access mode to EThernet mode

    *Question 63
    A company has a three-tier topology for its large data center and needs to extend Layer 2 connectivity with in the data center. What can be used to provide adequate stability, resiliency, and capacity?
    D. TRILL or SPBM to enhance the three-tier topology.

    *Question 64
    The switches in the exhibit form TRILL region_ How can the administrator encourage the switches to load-balance broadcasts, multicasts, and unknown unicasts
    over multiple switch-to-switch links?
    Ans:
    Specify the calculation of two trees on the switch With the highest TRILL root priority

    *Question 65
    An HP Comware switch connects to server Converged Network Adaptors (CNAs) on several interfaces. FCoE is set up on the switch for these connections.
    What must the administrator implement on these switch interfaces to ensure lossless delivery for the FCoE traffic?
    Ans:
    DCB eXchange (DCBX), Priority Flow Control (PFC), and Enhanced Transmission Selection (ETS)

    *Question 66
    Refer to the exhibit
    A data center that uses SPBM needs a Layer 3 solution to route traffic for the server subnets. How can administrators configure a core switch to accomplish this?
    Ans:
    Set up two MDCs. The first MDC runs SPBM and has a port with SPBM service instance for VLAN 10, 20, and 30. This port connects to a port on the second MDC which routes for the VLANs.

    *Question 67
    Refer to the exhibit
    All switches have established the EVI links shown in the exhibit. Each switch extends VLAN 10 on this EVI network.
    How is the MAC forwarding table for VLAN 10 switch 1 populated with MAC addresses in DC 2 and DC 3?
    Ans:
    EVI switches advertise their local VLAN 10 MAC addresses using IS-IS Switch 1 binds a remote MAC address to the EVI link that receives the IS-IS message.

    *Question 68
    An administrator is configuring HP Comware Switch 1 to support FCoE for connected servers with Converge Network Adaptors (CNAs). On Ten1/0/1, Switch 1
    sends FCoE traffic to an upstream switch also supports FCoE and connects to storage. What is the correct configuration for Switch1 Ten1/0/1?
    Ans:
    bound to a VFC interface, which is in E mode

    *Question 69
    Refer to the exhibit
    An administrator is setting up an MPLS Layer 2 VPN virtual circuit (VC) between customer Site 1 and 2. On PE-1 a pseudo wire (PW) was set up to PE-2 using
    a cross-connect group. What should the administrator consider when setting up a PW on PE-2 for traffic in the other direction?
    Ans:
    Create a PW pn PE-2 regardless of how the PW is configured on PE-1

    *Question 70
    An administrator is preparing to assign physical switch interfaces to MDCs on an HP Comware switch. What is an assignment rule?
    B. Each MDC has sole control over its interfaces, interfaces are assigned to an MDC on a port group basis.

    *Question 71
    Refer to the exhibit
    An administrator is configuring PE-1 to be part of the MPLS domain. The domain uses LDP. On witch interfaces should the administrator enable MPLS and LDP?
    Ans:
    Enable MPLS on Ten2/0/1 and Ten2/0/2. Enable LDP on Ten2/0/1 and Ten2/0/2

    *Question 72
    An administrator is configuring several HP Comware sw to supports FCoE in Fibre Channel Forwarder (FCF) mode. The switches should be part of the same VSAN or fabric. What is the correct method for setting the VSAN domain ID on the switches
    Ans:
    Set it manually as a unique value on each switch

    *Question 73
    A label switching router (LSR) knows open shortest path first (OSPF ) routes in the 10.0.0.0/15 range.an administrator wants the LSR to advertise network in the 10.1.0.0/16 range with LDP,However ,the LSR should not advertise in the 10.0.0.0/16 range.
    How can this goal be accomplished?
    Ans:
    Create an IP prefix listfor the 10.1.0.0/16 networks end specify that prefix list in the LDP trigger policy

    *Question 74
    An administrator is planning to enable priority flow control (PFC) on a switch port in auto mode. What is a difference in setup for auto mode compared to manual mode?
    Ans:
    DCBX TLVs must be enabled on this switch port

    *Question 75
    Which requirement must a data center network meet to support federated applications?
    A. Use a hierarchical design that divides the access layer from the core with a distribution layer.
    B. Provide insight into communications that occur entirely whitin a virtualized host.
    C. Support distributed rounting functions to ensure resiliency in all scenarios.
    D. Support a high volume of low latency communications between servers.
    Answer: D

    *Question 76
    Refer to the exhibit
    The switches shown in the exhibit are part of a TRILL solution. Switches 4 and 5 are HP 12900 Series switches and support MDC. Which benefit does HP MDC bring to the 12900 Serier switches in this solution?
    A. They can participate in the TRILL domain and also provide routing for the server VLANs in another MDC

    *Question 77
    An administrator wants to use Application TLVs to communicate application priority information to a Converged Networks Adapter (CNA) connected to interface Ten/1/0/1. The administrator has configured a QoS policy for this purpose. What are correct ways to apply this policy? (Select two)
    Ans:
    as an outboung global QoS policy
    as an outbound QoS policy on interface Ten1/0/1




    0



    0
  82. Jate.Adisorn says:

    Hey I’m pass with score 92% and my team follow me with 87%
    I collect these answer from Eddy and Serafino000 (thank both)
    and Upload as link.

    https://drive.google.com/file/d/0B9xm4EfHnyXcMFJ6dk8yRGtlUlU/view?usp=sharing

    This pdf has answer almost 100% right , but it has 78q, not full 80q.
    You can find else missing question as this link below.

    https://drive.google.com/file/d/0B9xm4EfHnyXcVDF3d05BbnpiMHM/view?usp=sharing

    I recommend find answer first with
    “1 HP2-Z34 -Pass sure – from Serafino and Eddy.pdf”

    If you not found some question , so find later with
    “2 serafino000_80q_with Some know Ans.pdf”

    I’m not comfirm this share will 100% right answer
    but I confirm 100% sure pass.

    Cr Eddy, Serafino000




    0



    0

Leave a Reply