which further steps must the network administrator perform?
View the exhibit.
A network administrator wants to configure an HP 5800 switch to place all incoming traffic on the
GigabitEthernet 1/0/1 port in priority queue 3. However, one exception applies. All traffic incoming
on that port that is destined to UDP port 55555 should be forwarded in priority queue 4 and
marked with DSCP 32.
Based on the current configurations shown in the exhibit, which further steps must the network
administrator perform? (Select two.)
Which technology does the HP Virtual Connect support?
Which technology does the HP Virtual Connect support?
What does this indicate?
Refer to the exhibit.
Exhibit Comware switch output.
A network administrator has implemented link aggregation on an HP Comware switch using
LACP. Assume the two ports are functioning at the data link layer between the Comware switch
neighboring switch. The network administrator execution display link-aggregation verbose
command and notices the flag of AG for the two links. As shown in the exhibit.
What does this indicate?
How can the network administrator configure the Comware switch to address this problem?
A company has a service level agreement (SLA) with its service provider. The SLA specifies a 2
Mbps committed information rate (CIR) and 20 KB committed burst size (CBS). Lately, during
peak usage times, the company has been experiencing brief periods of poor performance on its
external connection (GigabitEthernet port 2/0/1 on an HP 5800 switch).
How can the network administrator configure the Comware switch to address this problem?
What will be the outcome?
Refer to the exhibit.
Exhibit Switch configuration
A network administrator is configuring an aggregated link between an HP Comware and ProVision
switch. The network administrator applies the configurations to the switches, as shown in the
exhibit. The two links on the both switches are up, and they can see each other on both links in the
local LLDP table.
What will be the outcome?
Which step must the network administrator perform on each of these switches?
A network includes a mix of IGMPv2 and IGMPv3 endpoints and must support the following
source specific multicasting applications:
* Source: 10.1.4.2 and Group: 232.0.5.5
* Source: 10.1.4.12 and Group 232.0.6.6
The network is already implementing PIM-SM and IGMPv3. In order to support these applications,
the HP 10500 switches that act as routers for the endpoints in question must support another
feature. Which step must the network administrator perform on each of these switches?
which value is presented by default as the LLDP Chassis ID on both ProVision and Comware switches?
When LLDP is enabled, which value is presented by default as the LLDP Chassis ID on both
ProVision and Comware switches?
which switches should (*, 239.255.1.1) entries appear if the system is functioning correctly?
View the exhibit.
Exhibit 1
Exhibit 2
PIM-SM is configured on each interface in the network and IGMP is enabled on VLAN 3 and VLAN
4, as shown in Exhibit 1. Each switch has a rendezvous point (RP) set and valid unicast routes, as
shown in Exhibit 2.
The network administrator configures an endpoint connected to VLAN4 to begin listening on
239.255.1.1 to verify if multicast routing configuration is established correctly. The network is not
live, meaning no other hosts are sending IGMP requests. The network administrator then checks
PIM routing entries on the switches to verify if the system is functioning correctly.
On which switches should (*, 239.255.1.1) entries appear if the system is functioning correctly?
What is the default payload size for an 802.3 Ethernet frame on HP switches?
What is the default payload size for an 802.3 Ethernet frame on HP switches?
What is the initial OSPF state after an adjacency has formed?
Two OSPF routers are on a segment, and both of their interfaces become active. What is the initial
OSPF state after an adjacency has formed?