What must you do to resolve this problem?
— Exhibit —
[edit]
user@R1# run show interfaces ge-1/1/2 terse
Interface Admin Link Proto Local Remote
ge-1/1/2 up up
ge-1/1/2.0 up up aenet –> ae0.0
[edit]
user@R1# run show interfaces ge-1/1/3 terse
Interface Admin Link Proto Local Remote
ge-1/1/3 up up
ge-1/1/3.0 up up aenet –> ae0.0
[edit]
user@R1# run show interfaces ae0 terse
Interface Admin Link Proto Local Remote
ae0 up down
ae0.0 up down bridge
[edit]
user@R1# show interfaces ae0
aggregated-ether-options {
lacp {
periodic slow;
system-priority 200;
}
}
unit 0 {
family bridge {
interface-mode trunk;
vlan-id-list 100;
}
}
**************************************************************************
[edit]
user@R2# run show interfaces ge-1/1/2 terse
Interface Admin Link Proto Local Remote
ge-1/1/2 up up
ge-1/1/2.0 up up aenet –> ae0.0
[edit]
user@R2# run show interfaces ge-1/1/3 terse
Interface Admin Link Proto Local Remote
ge-1/1/3 up up
ge-1/1/3.0 up up aenet –> ae0.0
[edit]
user@R2# run show interfaces ae0 terse
Interface Admin Link Proto Local Remote
ae0 up down
ae0.0 up down bridge
[edit]
user@R2# show interfaces ae0
aggregated-ether-options {
lacp {
periodic fast;
system-priority 100;
}
}
unit 0 {
family bridge {
interface-mode trunk;
vlan-id-list 100;
}
}
— Exhibit —
You have configured a LAG and are now enabling LACP on the ae0 interface. You have
configured and committed the configuration as shown in the exhibit. However, the exhibit also
shows that the ae0 interface is now in the up/down state.
What must you do to resolve this problem?
which interface would be used to forward traffic to host 1.1.7.5?
Click the Exhibit button.
In the exhibit, which interface would be used to forward traffic to host 1.1.7.5?
Which policy action should router R3 configure to make this route visible on routers R1 and R2?
Click the Exhibit button.
A route is advertised from AS 65221 to AS 65432 using EBGP. The route is active and reachable
on R3, but does not appear as an active route on R1 and R2. R3 has an export policy applied to
its IBGP group matching on routes from R4, but does not have a then criteria specified. Which
policy action should router R3 configure to make this route visible on routers R1 and R2?
What are three policy types?
What are three policy types? (Choose three.)
Which command will allow you to configure the Ethernet 0/0 interface to have the IP address shown in the exhib
Click the Exhibit button.
Which command will allow you to configure the Ethernet 0/0 interface to have the IP address
shown in the exhibit?
what could be the source address/port of the packet arriving at host B?
Click the Exhibit button to view the exhibit.
If A initiates a Web browsing session with B, and the Trust interface of the 5XT is in NAT
mode, what could be the source address/port of the packet arriving at host B?
What can be done to enforce this behavior?
Click the Exhibit button.
R3 is announcing a route to R4 using EBGP, as shown in the exhibit. All routers in AS 65221
should learn this route, but it should not be announced to any other AS. What can be done to
enforce this behavior?
Study the exhibit carefully.
Exhibit:
You work as an administrator at Certkiller .com. Study the exhibit carefully.
what will be the source address of the packet arriving at host D?
Click the Exhibit button to view the exhibit.
If A initiates a Web browsing session with D, and the E1 interface of the 208 is in NAT mode,
what will be the source address of the packet arriving at host D?
Which choice shows the configuration in the exhibit in SLAX format?
Click the Exhibit button.
Which choice shows the configuration in the exhibit in SLAX format?
