which statement is correct?
Click the Exhibit button.
Based on the configuration in the exhibit, which statement is correct?
Which additional statement is necessary to establish the session?
You have the following BGP configuration in place to establish a session with a remote peer over
your ethernet4 interface.
set vrouter trust-vr protocol bgp 65000
set vrouter trust-vr protocol bgp enable
set vrouter trust-vr protocol bgp neighbor remote-as 65500
set vrouter trust-vr protocol bgp neighbor enable
Which additional statement is necessary to establish the session?
Which is NOT a component of a tunnel interface configuration?
Which is NOT a component of a tunnel interface configuration?
Which two statements are true?
You are monitoring the control plane traffic using a network analyzer on an Ethernet network
segment with all routers configured with IS-IS routing. Which two statements are true? (Choose
two.)
What could be causing this problem?
You have created your tunnel interface in the untrust zone. Traffic from the trust zone is able
to enter the tunnel and pass to the destination. However traffic from a different interface in
the untrust zone is not able to pass traffic through the tunnel. You are using a single virtual
router. What could be causing this problem?
which counter indicates a possible denial of service attack?
Click the Exhibit button.
— Exhibit —
user@R1> show pfe statistics traffic
Packet Forwarding Engine traffic statistics:
Input packets: 47593914461368 2 pps
Output packets: 28805646 3 pps
Packet Forwarding Engine local traffic statistics:
Local packets input : 36278104324
Local packets output : 2
Software input control plane drops : 0
Software input high drops : 0
Software input medium drops : 0
Software input low drops : 0
Software output drops : 0
Hardware input drops : 191367536738
Packet Forwarding Engine local protocol statistics:
HDLC keepalives : 0
ATM OAM : 0
Frame Relay LMI : 0
PPP LCP/NCP : 0
OSPF hello : 3883169
OSPF3 hello : 0
RSVP hello : 1440704
LDP hello : 4782297
BFD : 0
IS-IS IIH : 0
LACP : 0
ARP : 765512
ETHER OAM : 0
Unknown : 1897610
Packet Forwarding Engine hardware discard statistics:
Timeout : 0
Truncated key : 0
Bits to test : 0
Data error : 0
Stack underflow : 0
Stack overflow : 0
Normal discard : 191367536738
Extended discard : 0
Invalid interface : 0
Info cell drops : 191367536738
Fabric drops : 191367536738
Packet Forwarding Engine Input IPv4 Header Checksum Error and Output MTU Error statistics:
Input Checksum : 0
Output MTU : 0
— Exhibit —
Referring to the exhibit, which counter indicates a possible denial of service attack?
How should you configure your tunnel interface?
You want to minimize the number of IP addresses and subnets in use. How should you
configure your tunnel interface?
Which router should be configured to accomplish the administrative goal of the customer?
Click the Exhibit button.
In the exhibit, Customer A uses private RFC1918 addresses within its network. The customer
wants to have all Internet access for its organization transit through the main office for security and
NAT purposes. Each of the PE routers in your network contains Internet routes in the main
instance routing table and is capable of provisioning both a VRF and a non-VRF interface to its
attached CE router. Which router should be configured to accomplish the administrative goal of
the customer?
What is causing this problem?
You have created your tunnel interface in the untrust zone. Traffic from the trust zone is able
to enter the tunnel and pass to the destination. However traffic from a different interface in
the untrust zone is not able to pass traffic through the tunnel. You are using a single virtual
router. What is causing this problem?
what is the problem?
Click the Exhibit button.
Customer A is complaining that routes advertised from the CE2 router are not being received on
the CE1 router. The physical topology of the network is CE1-PE1-PE2-CE2. The CE1-PE1 subnet
is 172.16.1.0/24. The CE2-PE2 subnet is 172.16.2.0/24. PE1’s loopback is 192.168.3.1 and PE2’s
loopback is 192.168.4.1.Referring to the output in the exhibit, what is the problem?