– DS1( Distribute switch 1) is the primary device for Vlan 101, 102, 105
– DS2 ( Distribute switch 2) is the primary device for Vlan 103 and 104

During routine maintenance, G1/0/1 on DS1 was shutdown. All other interface were up. DS2
became the active HSRP device for Vlan101 as desired. However, after G1/0/1 on DS1 was
reactivated. DS1 did not become the active HSRP device as desired. What need to be done
to make the group for Vlan101 function properly?

– DS1( Distribute switch 1) is the primary device for Vlan 101, 102, 105
– DS2 ( Distribute switch 2) is the primary device for Vlan 103 and 104

DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces
are active. As related to Vlan103’s HSRP group. What can be done to make the group
function properly?

– DS1( Distribute switch 1) is the primary device for Vlan 101, 102, 105
– DS2 ( Distribute switch 2) is the primary device for Vlan 103 and 104

If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1?

– DS1( Distribute switch 1) is the primary device for Vlan 101, 102, 105
– DS2 ( Distribute switch 2) is the primary device for Vlan 103 and 104

What is the configured priority value of the Vlan105’s group on DS2?

– DS1( Distribute switch 1) is the primary device for Vlan 101, 102, 105
– DS2 ( Distribute switch 2) is the primary device for Vlan 103 and 104

During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All
other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP
group. As related to Vlan104’s HSRP group. What can be done to make the group function properly?

– DS1( Distribute switch 1) is the primary device for Vlan 101, 102, 105
– DS2 ( Distribute switch 2) is the primary device for Vlan 103 and 104

Which statement is correct about the use of the virtual interface on a WLC:

You work as a network engineer for your company. You are required to set up the network
being displayed in the network topology exhibit through the console using IOS commands.

You administer a network that uses two routers, R1 and R2, configured as an HSRP group
to provide redundancy for the gateway. Router R1 is the active router and has been
configured as follows:
R1#configure terminal
R1(config)#interface fa0/0
R1(config-if)#ip address 10.10.0.5 255.255.255.0
R1(config-if)#standby 1 priority 150
R1(config-if)#standby preempt delay minimum 50
R1(config-if)#standby 1 track interface fa0/2 15
R1(config-if)#standby 1 ip 10.10.0.20
Which of the following describes the effect the standby preempt delay minimum 50
command will have on router R1? (Select the best answer.)
The HSRP priority for router R1 will increase to 200.
Router R1 will become the standby router if the priority drops below 50.
The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
Router R1 will wait 50 seconds before attempting to preempt the active router.

Refer to the exhibit.

Which of the following should you do to configure the IP phone to override the priority of the
data packets it receives from the host? (Select the best answer.)

You want to configure a switched internetwork with multiple VLANs as shown above.
Which of the following commands should you issue on SwitchA for the port connected to SwitchB? (Select the best answer.)