You are troubleshooting an OSPF problem where external routes are not showing up in the
OSPF database. Which two options are valid checks that should be performed first to verify
proper OSPF operation? (Choose two.) Select 2 response(s).

When verifying the OSPF link state database, which type of LSAs should you expect to see
within the different OSPF area types? (Choose three.) Select 3 response(s).

When verifying OSPF virtual link problems, which is an important item to check on the two
transit OSPF routers? Select the best response.

You are developing a verification plan for an upcoming OSPF implementation. Part of this
plan is to verify the status of type 3 LSAs within the network. Which routers should you verify
first to ensure that the configurations are correct for generating type 3 LSAs?
Select the best response.

Which condition must be satisfied before an EIGRP neighbor can be considered a feasible
successor?
Select the best response.

Based on the need to limit processing and bandwidth utilization due to dynamic routing
protocol operation, the following routing requirements have been specified for your network.
– partial and incremental routing updates
– only the devices affected by a topology change perform route recomputation
– route recomputation only occurs for routes that were affected
Which dynamic routing protocol should be deployed in your network to best meet these
requirements?
Select the best response.

Which statement about a non-zero value for the load metric (k2) for EIGRP is true? Select
the best response.

Your network consists of a large hub-and-spoke Frame Relay network with a CIR of 56 kb/s
for each spoke. Which statement about the selection of a dynamic protocol is true?
Select the best response.

R3#show run | include default-ip default-network 140.140.0.0
ip default-network 130.130.0.0
R3#show ip route | begin Gateway
Gateway of last resort is 0.0.0.0 to network 130.130.0.0
116.0.0.0/8 is variably subnetted, 5 subnets, 3 masks
C 116.16.37.0/30 is directly connected, Serial1/0.2
C 116.16.32.0/30 is directly connected, Serial2/0.2
C 116.16.34.0/28 is directly connected, Serial1/0.1
C 116.16.35.0/28 is directly connected, Serial2/0.1
S 116.0.0.0/8 [1/0] via 116.16.34.0
* 140.140.0.0/32 is subnetted, 3 subnets
O 140.140.1.1 [110/65] via 116.16.34.4, 00:14:54, Serial1/0.1
O 140.140.3.1 [110/65] via 116.16.34.4, 00:14:54, Serial1/0.1
O 140.140.2.1 [110/65] via 116.16.34.4, 00:14:54, Serial1/0.1
* 130.130.0.0/16 is variably subnetted, 4 subnets, 2 masks
D* 130.130.0.0/16 is a summary, 00:30:04, Null0
C 130.130.1.0/24 is directly connected, Ethernet0/0
C 130.130.2.0/24 is directly connected, Ethernet0/1
C 130.130.3.0/24 is directly connected, Ethernet1/0
D 150.150.0.0/16 [90/679936] via 116.16.35.5, 00:02:58, Serial2/0.1
Refer to the above exhibit. Why is the 140.140.0.0 network not used as the gateway of last
resort even though it is configured first?
Select the best response.

router eigrp 123
redistribute ospf 123
network 116.16.35.0 0.0.0.255
network 130.130.0.0
auto-summary
!
router ospf 123
log-adjacency-changes
network 116.16.34.0 0.0.0.255 area 0
neighbor 116.16.34.4
Refer to the above exhibit. Why are the EIGRP neighbors for this router not learning the
routes redistributed from OSPF? Select the best response.